Model

Number

Input

Output

Load

Regulation

(%, Max)

Efficiency

(%, Typ)

Fuse Rating

Slow-Blow

(mA)

Voltage (VDC)

Current (mA)

Voltage

(VDC)

Current

(mA, Max)

Current

(mA, Min)

Nominal

Range

Full-Load

No-Load

D101EI

5

4.5 - 5.5

286

30

5.0

200.0

20.0

15

70

500

D102EI

5

4.5 - 5.5

267

30

9.0

111.0

12.0

15

75

500

D103EI

5

4.5 - 5.5

256

30

12.0

83.0

9.0

15

78

500

D104EI

5

4.5 - 5.5

250

30

15.0

67.0

7.0

15

80

500

D105EI

5

4.5 - 5.5

278

30

±5.0

±100.0

±10.0

15

72

500

D106EI

5

4.5 - 5.5

267

30

±9.0

±56.0

±6.0

15

75

500

D107EI

5

4.5 - 5.5

256

30

±12.0

±42.0

±5.0

15

78

500

D108EI

5

4.5 - 5.5

253

30

±15.0

±33.0

±4.0

15

79

500

D111EI

12

10.8 - 13.2

115

15

5.0

200.0

20.0

15

72

200

D112EI

12

10.8 - 13.2

110

15

9.0

111.0

12.0

15

76

200

D113EI

12

10.8 - 13.2

105

15

12.0

83.0

9.0

15

79

200

D114EI

12

10.8 - 13.2

103

15

15.0

67.0

7.0

15

81

200

D115EI

12

10.8 - 13.2

113

15

±5.0

±100.0

±10.0

15

74

200

D116EI

12

10.8 - 13.2

110

15

±9.0

±56.0

±6.0

15

76

200

D117EI

12

10.8 - 13.2

105

15

±12.0

±42.0

±5.0

15

79

200

D118EI

12

10.8 - 13.2

104

15

±15.0

±33.0

±4.0

15

80

200

D121EI

24

21.6 - 26.4

57

8

5.0

200.0

20.0

15

73

100

D122EI

24

21.6 - 26.4

54

8

9.0

111.0

12.0

15

77

100

D123EI

24

21.6 - 26.4

52

8

12.0

83.0

9.0

15

80

100

D124EI

24

21.6 - 26.4

51

8

15.0

67.0

7.0

15

82

100

D125EI

24

21.6 - 26.4

56

8

±5.0

±100.0

±10.0

15

74

100

D126EI

24

21.6 - 26.4

55

8

±9.0

±56.0

±6.0

15

76

100

D127EI

24

21.6 - 26.4

52

8

±12.0

±42.0

±5.0

15

80

100

D128EI

24

21.6 - 26.4

51

8

±15.0

±33.0

±4.0

15

81

100

Derating Curve

Notes:

Pin

Single

Dual

Pin

Single

Dual

1

+Vin

+Vin

6

No Pin

Common

2

-Vin

-Vin

7

+Vout

+Vout

5

-Vout

-Vout

Notes:

1. Output load regulation is specified for a load change of 10% to 100%.

2. These units should not be operated with a load under 10% of full load.

Operation at no-load may cause damage to the unit.

3. These converters will operate without external components. However,

when measuring output ripple, it is recommended that an external ceramic

capacitor be placed

from the +Vout pin to

the -Vout pin for single

output units and from

each output to common

for dual output units.

An input capacitor will

enhance stability over

temperature and input line variations. Recommended capacitor values are

given in the table above. For applications requiring very low output noise

levels, a simple LC filter should be effective.

4. Dual output units may be connected to provide a 10V, 18V, 24V or

30 VDC output. To do this, connect the load across the positive (+Vout) and

negative (-Vout) outputs and float the output common

5. It is recommended that a fuse be used on the input of a power supply for

protection. See the Model Selection table above for the correct rating.

Vin

Input

Capacitor

Vout

Output Capacitor

Single

Dual

5 VDC

4.7 μF

5 VDC

10.0 μF

4.7 μF

12 VDC

2.2 μF

9 VDC

4.7 μF

2.2 μF

24 VDC

1.0 μF

12 VDC

2.2 μF

1.0 μF

15 VDC

1.0 μF

0.47 μF

Other input/output combinations are available

(i.e. 3.3 VDC). Contact the factory for details at:

sales@micropowerdirect.com

Pin Connections

Model Selection Guide

Mechanical Dimensions

MicroPower Direct

www.micropowerdirect.com

292 Page Street Ste D Stoughton, MA 02072

•

TEL: (781) 344-8226

•

FAX: (781) 344-8481

•

E-Mail: sales@micropowerdirect.com