 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
LTC2755BIUP-16-TRPBF Datasheet(PDF) 11 Page - Linear Technology |
|
||||||||||||||||||||||||||||||
LTC2755BIUP-16-TRPBF Datasheet(HTML) 11 Page - Linear Technology |
|
|
11 / 24 page  LTC2755 11 2755f PIN FUNCTIONS READ (Pin 49): Read Pin. When READ is asserted high, the data I/O (D0-D15) or span I/O (S0-S2) port outputs the contents of the selected register (see Table 1). For single- span operation, readback of the span I/O pins is disabled, since they must be tied directly to GND and/or VDD. UPD (Pin 50): Update and Buffer Select Pin. When UPD is asserted high with READ held low, the contents of the addressed DAC’s input registers (both data and span) are copied into their respective DAC registers. The output of the DAC is updated, reflecting the new DAC register values. When READ is held high (during a read operation), the update function is disabled and the UPD pin functions as a buffer selector—logic low to read back the input register, high to read back the DAC register. See Readback in the Operation section. WR (Pin 51): Active Low Write Pin. A Write operation cop- ies the data present on the data or span I/O pins (D0-D15 or S0-S2, respectively) into the associated input register. When READ is high, the Write function is disabled. S1 (Pin 52): Span I/O Bit 1. Pins S0, S1 and S2 are used to program and to read back the output ranges of the DACs. REFB (Pin 53): Reference Input for DAC B. The imped- ance looking into this pin is 10k to ground. For normal operation tie this pin to the negative reference voltage at the output of reference inverting amplifier A1 (see Typical Applications). Typically –5V; accepts up to ±15V. ROFSB (Pin 54): Bipolar Offset Network for DAC B. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RIN1 (Pin 64). The impedance looking into this pin is 20k to ground. RFBB (Pin 55): DAC B Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC B (see Typical Applications). The DAC output current from IOUT1B flows through the feedback resistor to the RFBB pin. The impedance looking into this pin is 10k to ground. IOUT1B (Pin 56): DAC B Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC B (see Typical Applications). RVOSB (Pin 57): DAC B Offset Adjust. Nominal input range is ±5V. The impedance looking into this pin is 1M to ground. If not used, tie RVOSB to ground. RVOSA (Pin 58): DAC A Offset Adjust. Nominal input range is ±5V. The impedance looking into this pin is 1M to ground. If not used, tie RVOSA to ground. IOUT1A (Pin 59): DAC A Current Output. This pin is a virtual ground when the DAC is operating and should reside at 0V. For normal operation tie to the negative input of the I/V converter amplifier for DAC A (see Typical Applications). RFBA (Pin 60): DAC A Feedback Resistor. For normal operation tie to the output of the I/V converter amplifier for DAC A (see Typical Applications). The DAC output current from IOUT1A flows through the feedback resistor to the RFBA pin. The impedance looking into this pin is 10k to ground. ROFSA (Pin 61): Bipolar Offset Network for DAC A. This pin provides the translation of the output voltage range for bipolar spans. Accepts up to ±15V; for normal operation tie to the positive reference voltage at RIN1 (Pin 64). The impedance looking into this pin is 20k to ground. REFA (Pin 62): Reference Input for DAC A, and connec- tion for internal reference inverting resistor R2. The 20k resistor R2 is connected internally from RCOM1 to REFA. For normal operation tie this pin to the output of reference inverting amplifier A1 (see Typical Applications). Typically –5V; accepts up to ±15V. The impedance looking into this pin is 10k to ground (RIN1 and RCOM1 floating). RCOM1 (Pin 63): Center Tap Point for Reference Ampli- fier A1 Inverting Resistors. The 20k reference inverting resistors R1 and R2 are connected internally from RIN1 to RCOM1 and from RCOM1 to REFA, respectively (see Block Diagram). For normal operation tie RCOM1 to the negative input of external reference inverting amplifier A1 (see Typical Applications). RIN1 (Pin 64): Input Resistor R1 for Reference Inverting Amplifier A1. The 20k resistor R1 is connected internally from RIN1 to RCOM1. For normal operation tie RIN1 to the external reference voltage VREF1 (see Typical Applica- tions). Typically 5V; accepts up to ±15V. Exposed Pad (Pin 65): Ground. The Exposed Pad must be soldered to the PCB. |
Similar Part No. - LTC2755BIUP-16-TRPBF |
|
Similar Description - LTC2755BIUP-16-TRPBF |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
