Electronic Components Datasheet Search |
|
DRV602 Datasheet(PDF) 7 Page - Texas Instruments |
|
|
DRV602 Datasheet(HTML) 7 Page - Texas Instruments |
7 / 12 page Charge Pump Flying Capacitor and PVSS Capacitor Decoupling Capacitors Gain setting resistors ranges -In Rfb + - Inverting RIN CIN Rfb Rfb + - Differential Input -In +In CIN RIN RIN CIN RIN CIN +In Rfb Rx + - Cx Non Inverting DRV602 www.ti.com ........................................................................................................................................................................................... SLOS572 – DECEMBER 2008 The charge pump flying capacitor serves to transfer charge during the generation of the negative supply voltage. The PVSS capacitor must be at least equal to the charge pump capacitor in order to allow maximum charge transfer. Low ESR capacitors are an ideal selection, and a value of 1µF is typical. Capacitor values that are smaller than 1µF can be used, but the maximum output voltage may be reduced and the device may not operate to specifications. The DRV602 is a DirectPath Line Driver amplifier that require adequate power supply decoupling to ensure that the noise and total harmonic distortion (THD) are low. A good low equivalent-series-resistance (ESR) ceramic capacitor, typically 1µF, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to the DRV602 is important for the performance of the amplifier. For filtering lower frequency noise signals, a 10-µF or greater capacitor placed near the audio power amplifier would also help, but it is not required in most applications because of the high PSRR of this device. The gain setting resistors, RIN and Rfb, must be chosen so that noise, stability and input capacitor size of the DRV602 is kept within acceptable limits. Voltage gain is defined as Rfb divided by RIN. Selecting values that are too low demands a large input ac-coupling capacitor, CIN . Selecting values that are too high increases the noise of the amplifier. Table 1 lists the recommended resistor values for different gain settings. Table 1. Recommended Resistor Values INPUT RESISTOR FEEDBACK RESISTOR DIFFERENTIAL INPUT INVERTING INPUT GAIN NON INVERTING INPUT VALUE, RIN VALUE, Rfb GAIN GAIN 22 k Ω 22 k Ω 1.0 V/V –1.0 V/V 2.0 V/V 15 k Ω 30 k Ω 1.5 V/V –1.5 V/V 2.5 V/V 33 k Ω 68 k Ω 2.1 V/V –2.1 V/V 3.1 V/V 10 k Ω 100 k Ω 10.0 V/V –10.0 V/V 11.0 V/V Figure 6. Differential Input Figure 7. Inverting Figure 8. Non-Inverting Copyright © 2008, Texas Instruments Incorporated 7 Product Folder Link(s): DRV602 |
Similar Part No. - DRV602 |
|
Similar Description - DRV602 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |