 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
STPC4HDBI Datasheet(PDF) 80 Page - STMicroelectronics |
|
||||||||||||||||||||||||||||||
STPC4HDBI Datasheet(HTML) 80 Page - STMicroelectronics |
|
|
80 / 93 page  DESIGN GUIDELINES 80/93 Release 1.5 - January 29, 2002 The DIMM sockets should be populated starting with the furthest DIMM from the STPC device first (DIMM1). There are two types of DIMM devices; single-row and dual-row. The dual-row devices require two chip select signals to select between the two rows. A STPC device with 4 chip select control lines could control either 4 single-row DIMMs or 2 dual-row DIMMs. When only 2 chip select control lines are activated, only two single- row DIMMs or one dual-row DIMM can be controlled. When using DIMM modules, schematics have to be done carefully in order to avoid data buses completely crossing on the board. This has to be checked at the library level. In order to achieve the layout shown in Figure 6-21, schematics have to implement the crossing described in Figure 6-22. The DQM signals must be exchanged using the same order. 6.4.3.4. Summary For unbuffered DIMMs the address/control signals will be the most critical for timing. The simulations show that for these signals the best way to drive them is to use a parallel termination. For applications where speed is not so critical series termination can be used as this will save power. Using a low impedance such as 50 Ω for these critical traces is recommended as it both reduces the delay and the overshoot. The other memory interface signals will typically be not as critical as the address/control signals. Using lower impedance traces is also beneficial for the other signals but if their timing is not as critical as the address/control signals they could use the default value. Using a lower impedance implies using wider traces which may have an impact on the routing of the board. The layout of this interface can be validated by an electrical simulation using the IBIS model available on the STPC web site. Figure 6-21. Optimum Data Bus Layout for DIMM Figure 6-22. Schematics for Optimum Data Bus Layout for DIMM DIMM STPC SDRAM I/F D[15:00] D[31:16] D[47:32] D[63:48] MD[31:00] MD[63:32] MD[15:00],DQM[1:0] MD[31:16],DQM[3:2] MD[47:32],DQM[5:4] MD[63:48],DQM[7:6] D[15:00],DQM[1:0] D[31:16],DQM[3:2] D[47:32],DQM[5:4] D[63:48],DQM[7:6] DIMM STPC |
Similar Part No. - STPC4HDBI |
|
Similar Description - STPC4HDBI |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
