Electronic Components Datasheet Search |
|
L6910TR Datasheet(PDF) 6 Page - STMicroelectronics |
|
L6910TR Datasheet(HTML) 6 Page - STMicroelectronics |
6 / 29 page L6910 - L6910A 6/29 4.2 Reference A precise ±1.5% 0.9V reference is available. This reference must be filtered with 1nF ceramic capacitor to avoid instability in the internal linear regulator. It is able to deliver up to 100 µA and may be used as reference for the device regulation and also for other devices. If forced under 70% of its nominal value, the device enters in Hic- cup mode until this condition is removed. Through the EAREF pin the reference for the regulation is taken. This pin directly connects the non-inverting input of the error amplifier. An external reference (or the internal 0.9V ±1.5%) may be used. The input for this pin can range from 0.9V to 3V. It has an internal pull-down (300k Ω resistor) that forces the device shutdown if no reference is connected (pin floating). However the device is shut down if the voltage on the EAREF pin is lower than 650mV (typ). 4.3 Soft Start At start-up a ramp is generated charging the external capacitor CSS with an internal current generator. The initial value for this current is of 35 µA and speeds-up the charge of the capacitor up to 0.5V. After that it becames 10 µA until the final charge value of approximatively 4V. When the voltage across the soft start capacitor (VSS) reaches 0.5V the lower power MOS is turned on to dis- charge the output capacitor. As VSS reaches 1.1V (i.e. the oscillator triangular wave inferior limit) also the upper MOS begins to switch and the output voltage starts to increase. No switching activity is observable if SS is kept lower than 0.5V and both mosfets are off. If VCC and OCSET pins are not above their own turn-on thresholds and VEAREF is not above 650mV, the Soft- Start will not take place, and the relative pin is internally shorted to GND. During normal operation, if any under- voltage is detected on one of the two supplies, the SS pin is internally shorted to GND and so the SS capacitor is rapidly discharged. Figure 5. Soft Start (with Reference Present) 4.4 Driver Section The driver capability on the high and low side drivers allows using different types of power MOS (also multiple MOS to reduce the RDSON), maintaining fast switching transition. The low-side mos driver is supplied directly by Vcc while the high-side driver is supplied by the BOOT pin. Adaptative dead time control is implemented to prevent cross-conduction and allow to use several kinds of mos- fets. The upper mos turn-on is avoided if the lower gate is over about 200mV while the lower mos turn-on is Timing Diagram Vcc Turn-on threshold Vin Turn-on threshold 0.5V 1V Vcc Vin Vss LGATE Vout to GND Acquisition: CH1 = PHASE; CH2 = Vout; CH3 = PGOOD; CH4 = Vss |
Similar Part No. - L6910TR |
|
Similar Description - L6910TR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |