Electronic Components Datasheet Search |
|
M29F200T Datasheet(PDF) 14 Page - STMicroelectronics |
|
M29F200T Datasheet(HTML) 14 Page - STMicroelectronics |
14 / 33 page Symbol Alt Parameter Test Condition M29F200T / M29F200B Unit -55 -70 High Speed Interface Standard Interface Min Max Min Max tAVAV tRC Address Valid to Next Address Valid E = VIL,G= VIL 55 70 ns tAVQV tACC Address Valid to Output Valid E = VIL,G= VIL 55 70 ns tELQX (1) tLZ Chip Enable Low to Output Transition G = VIL 00 ns tELQV (2) tCE Chip Enable Low to Output Valid G = VIL 55 70 ns tGLQX (1) tOLZ Output Enable Low to Output Transition E=VIL 00 ns tGLQV (2) tOE Output Enable Low to Output Valid E = VIL 30 30 ns tEHQX tOH Chip Enable High to Output Transition G= VIL 00 ns tEHQZ (1) tHZ Chip Enable High to Output Hi-Z G = VIL 15 20 ns tGHQX tOH Output Enable High to Output Transition E=VIL 00 ns tGHQZ (1) tDF Output Enable High to Output Hi-Z E = VIL 15 20 ns tAXQX tOH Address Transition to Output Transition E=VIL,G= VIL 00 ns tPLYH (1,3) tRRB tREADY RP Low to Read Mode 10 10 µs tPHEL tRH RP High to Chip Enable Low 50 50 ns tPLPX tRP RP Pulse Width 500 500 ns tELBL tELBH tELFL tELFH Chip Enable to BYTE Switching Low or High 55 ns tBLQZ tFLQZ BYTE Switching Low to Output Hi-Z 15 20 ns tBHQV tFHQV BYTE Switching High to Output Valid 30 30 ns Notes: 1. Sampled only, not 100% tested. 2. G may be delayed by up to tELQV -tGLQV after the falling edge of E without increasing tELQV. 3. To be considered only if the Reset pulse is given while the memory is in Erase or Program mode. Table 14A. Read AC Characteristics (TA = 0 to 70 °C, –40 to 85°C or –40 to 125°C) Erase Suspend (ES) Instruction. The Block Erase operation may be suspended by this instruc- tion which consists of writing the command B0h without any specific address. No Coded cycles are required. It permits reading of data from another block and programming in another block while an erase operation is in progress. Erase suspend is accepted only during the Block Erase instruction execution. Writing this command during Erase timeout will, in addition to suspending the erase, terminate the timeout. The Toggle bit DQ6 stops togglingwhen the P/E.C. is suspended.The Toggle bits will stop toggling between 0.1 µs and 15µs after the Erase Suspend (ES) command has been writ- ten. The device will then automatically be set to Read Memory Array mode. When erase is sus- pended, a Read from blocks being erased will output DQ2 toggling and DQ6 at ’1’. A Read from 14/33 M29F200T, M29F200B |
Similar Part No. - M29F200T |
|
Similar Description - M29F200T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |