Electronic Components Datasheet Search |
|
M2764A-3F1 Datasheet(PDF) 3 Page - STMicroelectronics |
|
M2764A-3F1 Datasheet(HTML) 3 Page - STMicroelectronics |
3 / 10 page For the most efficient use of these two control lines, E should be decoded and used as the primary device selecting function, while G should be made a common connection to all devices in the array and connected to the READ line from the system control bus. This ensures that all deselected memory devices are in their low power standby mode and that the output pins are only active when data is desired from a particular memory device. System Considerations The power switching characteristics of fast EPROMs require careful decoupling of the devices. The supply current, ICC, has three segments that are of interest to the system designer: the standby current level, the active current level, and transient current peaks that are produced by the falling and rising edges of E. The magnitude of the transient current peaks is dependent on the capacitive and inductive loading of the device at the output. The associated transient voltage peaks can be sup- pressed by complying with the two line output control and by properly selected decoupling ca- pacitors. It is recommended that a 1 µF ceramic capacitor be used on every device between VCC and VSS. This should be a high frequency capacitor of low inherent inductance and should be placed as close to the device as possible. In addition, a 4.7 µF bulk electrolytic capacitor should be used between VCC and VSS for every eight devices. The bulk capacitor should be located near the power supply connection point. The purpose of the bulk capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces. Programming When delivered (and after each erasure for UV EPROM), all bits of the M2764A are in the “1" state. Data is introduced by selectively programming ”0s" into the desired bit locations. Although only “0s” will be programmed, both “1s” and “0s” can be present in the data word. The only way to change a “0" to a ”1" is by ultraviolet light erasure. The M2764A is in the programming mode when VPP input is at 12.5V and E and P are at TTL low. The data to be programmed is applied, 8 bits in parallel, to the data output pins. The levels required for the address and data inputs are TTL. Fast Programming Algorithm Fast Programming Algorithm rapidly programs M2764A EPROMs using an efficient and reliable method suited to the production programming en- vironment. Programming reliability is also ensured as the incremental program margin of each byte is continually monitored to determine when it has Mode E G PA9 VPP Q0 - Q7 Read VIL VIL VIH XVCC Data Out Output Disable VIL VIH VIH XVCC Hi-Z Program VIL VIH VIL Pulse X VPP Data In Verify VIL VIL VIH XVPP Data Out Program Inhibit VIH XXX VPP Hi-Z Standby VIH XXX VCC Hi-Z Electronic Signature VIL VIL VIH VID VCC Codes Out Note: X = VIH or VIL, VID = 12V ± 0.5%. Table 3. Operating Modes Identifier A0 Q7 Q6 Q5 Q4 Q3 Q2 Q1 Q0 Hex Data Manufacturer’s Code VIL 0010 00 00 20h Device Code VIH 0000 10 00 08h Table 4. Electronic Signature DEVICE OPERATION (cont’d) 3/10 M2764A |
Similar Part No. - M2764A-3F1 |
|
Similar Description - M2764A-3F1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |