M28W320FCT85N6E datasheet(14/69 Pages) NUMONYX

Part #	M28W320FCT85N6E

Description	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory

Download	69 Pages

Scroll/Zoom	100%

Manufacturer	NUMONYX [Numonyx B.V]

Direct Link	http://www.numonyx.com

Logo

14 / 69 page

Bus operations

M28W320FCT, M28W320FCB

14/69

3

Bus operations

There are six standard bus operations that control the device. These are Bus Read, Bus

Write, Output Disable, Standby, Automatic Standby and Reset. See Table 2: Bus

Operations, for a summary.

Typically glitches of less than 5ns on Chip Enable or Write Enable are ignored by the

memory and do not affect bus operations.

3.1

Read

Read Bus operations are used to output the contents of the Memory Array, the Electronic

Signature, the Status Register and the Common Flash Interface. Both Chip Enable and

Output Enable must be at VIL in order to perform a read operation. The Chip Enable input

should be used to enable the device. Output Enable should be used to gate data onto the

output. The data read depends on the previous command written to the memory (see

Command Interface section). See Figure 8: Read AC Waveforms, and Table 16: Read AC

Characteristics, for details of when the output becomes valid.

Read mode is the default state of the device when exiting Reset or after power-up.

3.2

Write

Bus Write operations write Commands to the memory or latch Input Data to be

programmed. A write operation is initiated when Chip Enable and Write Enable are at VIL

with Output Enable at VIH. Commands, Input Data and Addresses are latched on the rising

edge of Write Enable or Chip Enable, whichever occurs first.

See Figure 9 and Figure 10, Write AC Waveforms, and Table 17 and Table 18, Write AC

Characteristics, for details of the timing requirements.

3.3

Output Disable

The data outputs are high impedance when the Output Enable is at VIH.

3.4

Standby

Standby disables most of the internal circuitry allowing a substantial reduction of the current

consumption. The memory is in stand-by when Chip Enable is at VIH and the device is in

read mode. The power consumption is reduced to the stand-by level and the outputs are set

to high impedance, independently from the Output Enable or Write Enable inputs. If Chip

Enable switches to VIH during a program or erase operation, the device enters Standby

mode when finished.

Similar Part No. - M28W320FCT85N6E

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M28W320FCT85N6E	514Kb / 69P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory

More results

Similar Description - M28W320FCT85N6E

Manufacturer	Part #	Datasheet	Description
STMicroelectronics	M28W320CT	414Kb / 42P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory
	M28W320BT	211Kb / 43P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory May 2002
	M28W320EBT	299Kb / 45P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory
	M28W320ECT	832Kb / 53P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory
	M28W320FCT	514Kb / 69P	32 Mbit (2Mb x16, Boot Block) 3V Supply Flash Memory
	M29W320DT	524Kb / 56P	32 Mbit 4Mb x8 or 2Mb x16, Boot Block 3V Supply Flash Memory
	M29W320ET	887Kb / 46P	32 Mbit (4Mb x8 or 2Mb x16, Boot Block) 3V Supply Flash Memory
	M58LW032A	856Kb / 61P	32 Mbit 2Mb x16, Uniform Block, Burst 3V Supply Flash Memory
	M58LW032C	845Kb / 61P	32 Mbit 2Mb x16, Uniform Block, Burst 3V Supply Flash Memory
	M58LW032D	799Kb / 50P	32 Mbit (4Mb x8, 2Mb x16, Uniform Block) 3V Supply Flash Memory

More results

M28W320FCT85N6E Datasheet(PDF) 14 Page - Numonyx B.V

M28W320FCT85N6E Datasheet(HTML) 14 Page - Numonyx B.V

Similar Part No. - M28W320FCT85N6E

Similar Description - M28W320FCT85N6E

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69

Datasheet Download

Link URL