Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

CY8C9520A Datasheet(PDF) 8 Page - Cypress Semiconductor

Part # CY8C9520A
Description  20-, 40-, and 60-Bit IO Expander with EEPROM
Download  24 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  CYPRESS [Cypress Semiconductor]
Direct Link  http://www.cypress.com
Logo CYPRESS - Cypress Semiconductor

CY8C9520A Datasheet(HTML) 8 Page - Cypress Semiconductor

Back Button CY8C9520A Datasheet HTML 4Page - Cypress Semiconductor CY8C9520A Datasheet HTML 5Page - Cypress Semiconductor CY8C9520A Datasheet HTML 6Page - Cypress Semiconductor CY8C9520A Datasheet HTML 7Page - Cypress Semiconductor CY8C9520A Datasheet HTML 8Page - Cypress Semiconductor CY8C9520A Datasheet HTML 9Page - Cypress Semiconductor CY8C9520A Datasheet HTML 10Page - Cypress Semiconductor CY8C9520A Datasheet HTML 11Page - Cypress Semiconductor CY8C9520A Datasheet HTML 12Page - Cypress Semiconductor Next Button
Zoom Inzoom in Zoom Outzoom out
 8 / 24 page
background image
CY8C9520A, CY8C9540A
CY8C9560A
Document Number: 38-12036 Rev. *B
Page 8 of 24
PIN Descriptions
Extendable Soft Addressing™
The A0 line defines the corresponding bit of the I2C address.
This pin must be pulled up or down. If A0 is a strong pull up or a
strong pull down (wired through 330 or less resistor to Vdd or
Vss), then that is the only address line being specified and the
A1-A6 lines are used as GPIO. If A0 is a weak pull up or a weak
pull down (connected to Vdd or Vss through 75K- 200K ohm
resistor), then A0 is not the only externally defined address bit.
There is a pin assigned to be A1 if it is needed. This pin can be
pulled up or pulled down strong or weak with a resistor. As with
A0, the type of pull determines whether the address bit is the last
externally defined address bit. Differently from A0, A1 is not
dedicated as an address pin. It is only used if A0 is not the only
address bit externally defined. There are also predefined pins for
A2, A3, A4, A5, and A6 that is only used for addressing if needed.
The last address bit in the chain is pulled strong. That way, only
the number of pins needed to assign the address desired for the
part are allocated as address pins, any pins not used for address
bits can be used as GPIO pins. The Table 2, “Device
Addressing,” on page 3 defines the resulting device I2C address.
Interrupt Pin (INT)
The interrupt output (if enabled) is activated if one of these
events occurs:
One of the GPIO port pins changes state and the corresponding
bit in the Interrupt Mask register is set low.
When a PWM driven by the slowest clock source (367.6 Hz)
and assigned to a pin changes state and the pin’s corre-
sponding bit in the Interrupt Mask register is set low.
The interrupt line is deactivated when the master device
performs a read from the corresponding Interrupt Status register.
Write Disable Pin (WD)
If this feature is enabled, ‘0’ allows writes to the EEPROM and
‘1’ blocks any memory writes. This pin is checked immediately
before performing any write to memory. If the EEE bit in the
Enable register is not set (EEPROM disabled) or bit EERO is set
(EEPROM is read-only) then WD line level is ignored.
Note that ‘1’ on this line blocks all commands that perform opera-
tions with EEPROM (see Table 15, “Available Commands,” on
page 13).
This line may be enabled/disabled by bit 1 of the Enable register
(2Dh): ‘1’ enables WD function, ‘0’ disables.
External Reset Pin (XRES)
A full device reset is caused by pulling the XRES pin high. The
XRES pin has an always-on pull down resistor, so it does not
require an external pull down for operation. It can be tied
directly to ground or left open. Behavior after XRES is similar to
POR.
Working with PWMs
There are four independent PWMs in the CY8C9520A, eight in
the CY8C9540A and sixteen in the CY8C9560A. Each IO pin
can be configured as a PWM output by writing ‘1’ to the corre-
sponding bit of the Select PWM register (see Table 8, “Output
and Select PWM Registers Logic,” on page 11).
The next step of PWM configuration is clock source selection
using the Config PWM registers. There are six available clock
sources: 32 kHz (default), 24 MHz, 1.5 MHz, 93.75 kHz, 367.6
Hz or previous PWM output. (see Figure 5)
Figure 5. Clock Sources
By default, 32 kHz is selected as the PWM clock.
PWM Period registers are used to set the output period:
Allowed values are between 1 and FFh.
The PWM Pulse Width register sets the duration of the PWM
output pulse. Allowed values are between zero and the
(Period-1) value. The duty cycle ratio is computed using thsi
equation:
Divider (1-255)
93.75 kHz
367.6 Hz -
93.75 kHz
1.5 mHz
24 mHz
32 kHz
t
OUT
Period
t
CLK
×
=
DutyCycle
PulseWidth
Period
------------------------------
=
[+] Feedback


Similar Part No. - CY8C9520A

ManufacturerPart #DatasheetDescription
logo
Cypress Semiconductor
CY8C9520A CYPRESS-CY8C9520A Datasheet
742Kb / 32P
   20, 40, and 60 Bit I/O Expander with EEPROM
CY8C9520A-24PVXI CYPRESS-CY8C9520A-24PVXI Datasheet
742Kb / 32P
   20, 40, and 60 Bit I/O Expander with EEPROM
CY8C9520A-24PVXIT CYPRESS-CY8C9520A-24PVXIT Datasheet
742Kb / 32P
   20, 40, and 60 Bit I/O Expander with EEPROM
CY8C9520A CYPRESS-CY8C9520A_10 Datasheet
742Kb / 32P
   20, 40, and 60 Bit I/O Expander with EEPROM
More results

Similar Description - CY8C9520A

ManufacturerPart #DatasheetDescription
logo
Cypress Semiconductor
CY8C9520A CYPRESS-CY8C9520A_10 Datasheet
742Kb / 32P
   20, 40, and 60 Bit I/O Expander with EEPROM
CY8C9520 CYPRESS-CY8C9520 Datasheet
374Kb / 25P
   20-, 40-, and 60-Bit I/O Expander with EEPROM
logo
Maxwell Technologies
79C2040 MAXWELL-79C2040 Datasheet
469Kb / 17P
   20 Megabit (512K x 40-Bit) EEPROM MCM
79LV2040 MAXWELL-79LV2040 Datasheet
471Kb / 17P
   20 Megabit (512K x 40-Bit) Low Voltage EEPROM MCM
logo
Intersil Corporation
HI5767 INTERSIL-HI5767 Datasheet
133Kb / 13P
   10-Bit, 20/40/60 MSPS A/D Converter with Internal Voltage Reference
logo
Renesas Technology Corp
M66013FP RENESAS-M66013FP Datasheet
88Kb / 5P
   8-bit I/O Expander with Address
logo
Schneider Electric
TM221C40R SCHNEIDER-TM221C40R Datasheet
263Kb / 17P
   controller M221 40 IO relay
logo
Mitsubishi Electric Sem...
M66013FP MITSUBISHI-M66013FP Datasheet
33Kb / 2P
   8-BIT I/O EXPANDER WITH ADDRESS
M66009FP MITSUBISHI-M66009FP Datasheet
73Kb / 8P
   8-BIT I/O EXPANDER WITH 5-BIT ADDRESS
logo
Renesas Technology Corp
M66009FP RENESAS-M66009FP Datasheet
2Mb / 9P
   8-BIT I/O EXPANDER WITH 5-BIT ADDRESS
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com