Electronic Components Datasheet Search |
|
L6926 Datasheet(PDF) 4 Page - STMicroelectronics |
|
L6926 Datasheet(HTML) 4 Page - STMicroelectronics |
4 / 8 page L6926D 4/8 OPERATION DESCRIPTION The main loop uses slope compensated PWM current mode architecture. Each cycle the high side MOSFET is turned on, triggered by the oscillator, so that the current flowing through it (the same as the inductor current) increases. When this current reaches the threshold (set by the output of the error amplifier E/A), the peak current limit comparator PEAK_CL turns off the high side MOSFET and turns on the low side one until the next clock cycle begins or the current flowing through it goes down to zero (ZERO CROSSING comparator). The peak in- ductor current required to trigger PEAK_CL depends on the slope compensation signal and on the output of the error amplifier. In particular, the error amplifier output depends on the VFB pin voltage. When the output current increases, the output capacitor is discharged and so the VFB pin decreases. This produces increase of the error amplifier out- put, so allowing a higher value for the peak inductor current. For the same reason, when due to a load transient the output current decreases, the error amplifier output goes low, so reducing the peak inductor current to meet the new load requirements. The slope compensation signal allows the loop stability also in high duty cycle conditions (see related section) Figure 1. Device Block Diagram Modes of Operation Depending on the SYNC pin value the device can operate in low consumption or low noise mode. If the SYNC pin is high (higher than 1.3V) the low consumption mode is selected while the low noise mode is selected if the SYNC pin is low (lower than 0.5V). Low Consumption Mode In this mode of operation, at light load, the device operates discontinuously based on the COMP pin voltage, in order to keep the efficiency very high also in these conditions. While the device is not switching the load dis- charges the output capacitor and the output voltage goes down. When the feedback voltage goes lower than the internal reference, the COMP pin voltage increases and when an internal threshold is reached, the device starts to switch. In these conditions the peak current limit is set approximately in the range of 200mA-400mA, depending on the slope compensation (see related section). Once the device starts to switch the output capacitor is recharged. The feedback pin increases and, when it reaches a value slightly higher than the reference voltage, the output of the error amplifier goes down until a clamp is activated. At this point, the device stops to switch. In this phase, most of the internal circuitries are off, so reducing the device consumption down to a typical value of 25 µA. VCC SYNC COM P P GOOD GND DRIVER GND GND GND PEAK CL VALLEY CL Vcc ZERO CROSSING LOOP CONTROL OSCILLATOR LOW NOISE/ CONSUM PTION LX OVP V REF FB E/A P GOOD POWER P MOS POWER N MOS SENSE P MOS SENSE N MOS Vcc 0.6V V REF 0.9V SLOP E RUN VCC SYNC COM P P GOOD GND DRIVER GND GND GND PEAK CL VALLEY CL Vcc ZERO CROSSING LOOP CONTROL OSCILLATOR LOW NOISE/ CONSUM PTION LX OVP V REF FB E/A P GOOD POWER P MOS POWER N MOS SENSE P MOS SENSE N MOS Vcc 0.6V V REF 0.9V SLOP E RUN |
Similar Part No. - L6926 |
|
Similar Description - L6926 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |