Electronic Components Datasheet Search |
|
L6920 Datasheet(PDF) 9 Page - STMicroelectronics |
|
L6920 Datasheet(HTML) 9 Page - STMicroelectronics |
9 / 13 page 9/13 L6920 Table 7. Capacitors distributors main list 5.3 Inductor selection Usually, inductors ranging between 5 µH to 40µH satisfy most of the applications. Small value inductors have smaller physical size and guarantee a faster response to load transient but in steady state condition a bigger ripple on output voltage is generated. In fact the output ripple voltage is given by Ipeak multiplied by ESR. Furthermore, as shown in equation (1), inductor size affects also the maximum current de- liverable to the load. Lastly, a low series resistance is suggested if very high efficiency values are needed. Any- way, the saturation current of the choke should be higher than the peak current limit of the device (1A). Good surface mounting inductors are available from COILCRAFTS, COILTRONICS, MURATA and other souc- es. In the following table are listed some suggested components. Table 8. Inductors distributors main list 5.4 Layout Guidelines The board layout is very important in order to minimize noise, high frequency resonance problems and electro- magnetic interference. It is essential to keep as small as possible the high switching current circulating paths to reduce radiation and resonance problems. So, the output and input cap should be very close to the device. The external resistor dividers, if used, should be as close as possible to the pins of the device (FB and LBI) and as far as possible from the high current circulating paths, to avoid pick up noise. Large traces for high current paths and an extended groundplane, help to reduce the noise and increase the efficiency. For an example of recommended layout see the following evaluation board. Manufacturer Series Cap Value ( µF) Rated Voltage (V) ESR (m Ω) AVX TPS 15 to 470 6.3 50 to 1500 KEMET T510/T494/ T495 10 to 470 6 30 to 1000 PANASONIC EEFCD 22 to 47 6.3 50 to 700 SANYO POSCAP TPA/B/C 22 to 230 6.3 40 to 80 SPRAGUE 595D 100 to 390 6.3 160 to 700 Manufacturer Series Inductor Value (uH) Saturation Current (A) Coilcraft DO1813HC 22 to 33 1 to 1.2 DO1608 4.7 to 15 0.9 to 1.5 Coiltronics UP1B 22 to 33 1 to 1.2 TP3 4.7 to 15 0.97 to 1.6 BI HM76-2 22 to 33 1 to 1.2 HM76-1 4.7 to 10 1 to 1.5 Murata LQN6C 10 to 22 1.2 to 1.7 Panasonic ELL6SH 10 to 22 0.9 to 1.5 ELL6RH 5.1 to10 11 to 1.55 Sumida CR43 4.7 to 10 0.84 to 1.15 |
Similar Part No. - L6920 |
|
Similar Description - L6920 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |