SN54LVTH652, SN74LVTH652

3.3V ABT OCTAL BUS TRANSCEIVERS AND REGISTERS

WITH 3STATE OUTPUTS

SCBS706F − AUGUST 1997 − REVISED OCTOBER 2003

6

POST OFFICE BOX 655303

electrical characteristics over recommended operating free-air temperature range (unless

otherwise noted)

PARAMETER

TEST CONDITIONS

SN54LVTH652

SN74LVTH652

UNIT

PARAMETER

TEST CONDITIONS

MIN

TYP†

MAX

MIN

TYP†

MAX

UNIT

VIK

VCC = 2.7 V,

II = −18 mA

−1.2

−1.2

V

VCC = 2.7 V to 3.6 V,

IOH = −100 µA

VCC−0.2

VCC−0.2

VOH

VCC = 2.7 V,

IOH = −8 mA

2.4

2.4

V

VOH

VCC = 3 V

IOH = −24 mA

2

V

VCC = 3 V

IOH = −32 mA

2

VCC = 2.7 V

IOL = 100 µA

0.2

0.2

VCC = 2.7 V

IOL = 24 mA

0.5

0.5

VOL

IOL = 16 mA

0.4

0.4

V

VOL

VCC = 3 V

IOL = 32 mA

0.5

0.5

V

VCC = 3 V

IOL = 48 mA

0.55

IOL = 64 mA

0.55

Control inputs

VCC = 3.6 V,

VI = VCC or GND

±1

±1

Control inputs

VCC = 0 or 3.6 V,

VI = 5.5 V

10

10

II

VI = 5.5 V

20

20

µA

II

A or B ports‡

VCC = 3.6 V

VI = VCC

1

1

µA

A or B ports‡

VCC = 3.6 V

VI = 0

−5

−5

Ioff

VCC = 0,

VI or VO = 0 to 4.5 V

±100

µA

VCC = 3 V

VI = 0.8 V

75

75

II(hold) A or B ports

VCC = 3 V

VI = 2 V

−75

−75

µA

II(hold) A or B ports

VCC = 3.6 V§

VI = 0 to 3.6 V

±500

µA

IOZPU

VCC = 0 to 1.5 V, VO = 0.5 to 3 V,

OE/OE = don’t care

±100∗

±100

µA

IOZPD

VCC = 1.5 V to 0, VO = 0.5 to 3 V,

OE/OE = don’t care

±100∗

±100

µA

VCC = 3.6 V, IO = 0,

Outputs high

0.19

0.19

ICC

VCC = 3.6 V, IO = 0,

VI = VCC or GND

Outputs low

5

5

mA

ICC

VI = VCC or GND

Outputs disabled

0.19

0.19

mA

∆ICC¶

VCC = 3 V to 3.6 V, One input at VCC − 0.6 V,

Other inputs at VCC or GND

0.2

0.2

mA

Ci

VI = 3 V or 0

4

4

pF

Cio

VO = 3 V or 0

9

9

pF

∗ On products compliant to MIL-PRF-38535, this parameter is not production tested.

† All typical values are at VCC = 3.3 V, TA = 25°C.

‡ Unused terminals at VCC or GND

§ This is the bus-hold maximum dynamic current. It is the minimum overdrive current required to switch the input from one state to another.

¶ This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND.

PRODUCT PREVIEW information concerns products in the formative or

design phase of development. Characteristic data and other

specifications are design goals. Texas Instruments reserves the right to

change or discontinue these products without notice.