Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF


IRDCIP1001-A Datasheet(PDF) 1 Page - International Rectifier

Part No. IRDCIP1001-A
Description  IRDCiP1001-A, 200kHz, 20A, 3.3VIN to 4.5VIN Single Phase Synchronous Buck Converter using iP1001
Download  6 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  IRF [International Rectifier]
Homepage  http://www.irf.com
Logo 

   
 1 page
background image
09/11/02
IRDCiP1001-A, 200kHz, 20A, 3.3V
IN to 4.5VIN Single Phase
Synchronous Buck Converter using iP1001
Overview
In this document, Table 1 and Figure 1 are provided to enable engineers to
easily evaluate the iP1001 in a single phase configuration that is capable of
providing up to 20A in a lab environment without airflow. Figures 3, 4, 5 and
6 and the complete bill of materials in Table 2 are provided as a reference
design to enable engineers to very quickly and easily design a single phase
converter. In order to optimize this design to your specific requirements,
refer to the iP1001 data sheet for guidelines on external component selection
and user adjustable limits and specifications. Custom designs may require
layout modifications.
Demoboard Quick Start Guide
Initial Settings:
The output is set to 2V, but can be adjusted from 0.925V to 2.0V by
setting SW1 according to the VID codes provided in Table 1. The output voltage can also be adjusted to allow up to
2.5V
OUT for 3.3VIN, by adding R3 & R4 with the DAC set to 2VOUT. Refer to equation 1 for R3 & R4 values. R4 should
be removed for output voltages below 2V, and R3 should be set to zero ohms (see Table 2).
The switching frequency is centered around 200kHz for <5V
IN applications with the FREQ pin connected to VDD.
The input voltage range can be increased to allow operation between 5V
IN and 12VIN. Refer to IRDCiP1001-B reference
design documentation for direction on changing the configuration of the demo board.
Procedure for Connecting and Powering Up Demoboard:
1. Apply input voltage (3.3V-4.5V) across V
IN and PGND. Note that this demo board has a mini-boost circuit
provided in order to provide the 5V
DD internal logic for the iP1001. This boost circuit can be used to provide power for
up to 5 x iP1001 devices simultaneously.
2. Apply load across VOUT pad and PGND pad.
3. Make sure Jumpers JP2 and JP3 are connected.
4. Remove jumper JP1 to turn on the boost circuit and pull iP1001 ENABLE pin high. The ENABLE pin is controlled via switch
8 on SW1. This pin is supplied in low state, once pulled high the output is enabled.
5. Adjust load accordingly.
IRDCiP1001-A Recommended Operating Conditions
(refer to the iP1001 datasheet for maximum operating conditions)
Input voltage:
3.3 - 4.5V (V
DD provided by mini boost circuit)
Output voltage:
DAC selectable between 0.925V - 2.0V (with extended operating range to 3.3V with R3 & R4)
Output current:
Up to 20A depending on duty factor (refer to recommended operating area Fig.1).
Switching Freq:
200kHz or 300kHz selectable.
IRDCiP1001-A
International Rectifier
233 Kansas Street, El Segundo, CA 90245 USA
REFERENCE DESIGN
REFERENCE DESIGN
Min
Max
VIN
3.3V
4.5V
VOUT
0.925V
2.5V
IOUT
See Fig.1
IRDCiP1001-A Demoboard
Operatng Conditions




Html Pages

1  2  3  4  5  6 


Datasheet Download



Related Electronics Part Number

Part NumberComponents DescriptionHtml ViewManufacturer
IRDCIP1001-B200kHz to 300kHz 20A 5VIN to 12VIN Single Phase Synchronous Buck Converter using iP1001 1 2 3 4 5 MoreInternational Rectifier
IRDCIP2002-C1MHz 120A 4-phase Synchronous Buck Converter using iP2002 1 2 3 4 5 MoreInternational Rectifier
IRDCIP1201-A300kHz Dual 15A 3.14V IN to 5.5V IN Dual Output Synchronous Buck Converter using iP1201 1 2 3 4 5 MoreInternational Rectifier
SC1961.5A Synchronous Buck Converter with Integrated Power Devices 1 2 3 4 5 MoreSemtech Corporation
RT9202SINGLE SYNCHRONOUS BUCK PWM DC-DC CONTROLLER 1 2 3 4 5 MoreRichtek Technology Corporation
SC196A1.5A Synchronous Buck Converter with Integrated Power Devices 1 2 3 4 5 MoreSemtech Corporation
RT9202_07Single Synchronous Buck PWM DC-DC Controller 1 2 3 4 5 MoreRichtek Technology Corporation
EPR-48Engineering Prototype Report for EP48 - 1.4 W Non-Isolated Buck Converter Using LNK304P 1 2 3 4 5 MorePower Integrations, Inc.
SC192Synchronous Buck Converter with Integrated Power Devices 1 2 3 4 5 MoreSemtech Corporation

Link URL

Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Bookmark   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl