Electronic Components Datasheet Search |
|
SC900AEVB Datasheet(PDF) 14 Page - Semtech Corporation |
|
SC900AEVB Datasheet(HTML) 14 Page - Semtech Corporation |
14 / 23 page 14 © 2005 Semtech Corp. www.semtech.com POWER MANAGEMENT SC900A Using the I2C Interface The SC900A is a read-write slave mode I2C device and complies with the Philips I2C standard version 2.1 dated January 2000. The SC900A has six user-accessible internal 8-bit registers. The I2C interface has been designed for program flexibility, in that once the slave address has been sent to the SC900A enabling it to be a slave transmitter/receiver, any register can be written to or read from independently of each other. While there is no auto increment/decrement capability in the SC900A I2C logic, a tight software loop can be designed to randomly access the next register indepen- dent of which register you have been accessing. The start and stop commands frame the datapacket and the repeat start condition is allowed if necessary. SC900A Limitations to the I2C Specifications Seven-bit addressing is required for communication with the SC900A; ten-bit addressing is not allowed. Any general call address will be ignored by the SC900A. Note that the SC900A is not CBUS compatible. Finally, the SC900A can operate in standard mode (100kbit/s) or fast mode (400kbit/s). Supported Formats Direct Format - Write The simplest format for an I2C write is the direct format. After the start condition [S], the slave address is sent, followed by an eighth bit indicating a write. The SC900A I2C then acknowledges that it is being addressed, and the master re- sponds with an 8-bit data byte consisting of the register address. The slave acknowledges and the master sends the appropriate 8-bit data byte. Once again the slave acknowledges and the master terminates the transfer with the stop condition [P]. Slave Address Register Address Data S W A AA P S: Start Condition Slave Address: 7 bit W: Write = ‘0’ Register Address: 8 bit A: Acknowledge (sent by slave) Data: 8 bit P: Stop condition I 2C Direct Format - Write Combined Format - Read After the start condition [S], the slave address is sent, followed by an eighth bit indicating a write. The SC900A I2C then acknowledges that it is being addressed, and the master responds with an 8-bit data byte consisting of the reg- ister address. The slave acknowledges and the master sends the repeated start condition [Sr]. Once again the slave address is sent, followed by an eighth bit indicating a read. The slave responds with an acknowledge and the previ- ously addressed 8-bit data byte. The master then sends a non-acknowledge (NACK). Finally the master terminates the transfer with the stop condition [P]. Slave Address Register Address Slave Address Data NACK S W A A Sr R A P S: Start Condition Slave Address: 7 bit W: Write = ‘0’ Register Address: 8 bit R: Read = ‘1’ Data: 8 bit A: Acknowledge (sent by slave) NACK: Non-Acknowledge (sent by master) Sr: Repeated Start Condition P: Stop condition I 2C Combined Format - Read Applications Information (Cont.) |
Similar Part No. - SC900AEVB |
|
Similar Description - SC900AEVB |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |