 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
P51XAG33KBA Datasheet(PDF) 5 Page - NXP Semiconductors |
|
||||||||||||||||||||||||||||||
P51XAG33KBA Datasheet(HTML) 5 Page - NXP Semiconductors |
|
|
5 / 36 page  Philips Semiconductors Product specification XA-G3 XA 16-bit microcontroller family 32K/512 OTP/ROM/ROMless, watchdog, 2 UARTs 1999 Apr 07 5 PIN DESCRIPTIONS MNEMONIC PIN. NO. TYPE NAME AND FUNCTION MNEMONIC PLCC LQFP TYPE NAME AND FUNCTION VSS 1, 22 16 I Ground: 0V reference. VDD 23, 44 17 I Power Supply: This is the power supply voltage for normal, idle, and power down operation. P0.0 – P0.7 43–36 37–30 I/O Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. Port 0 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 0 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. When the external program/data bus is used, Port 0 becomes the multiplexed low data/instruction byte and address lines 4 through 11. P1.0 – P1.7 2–9 40–44, 1–3 I/O Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type. Port 1 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 1 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. Port 1 also provides special functions as described below. 2 40 O A0/WRH: Address bit 0 of the external address bus when the external data bus is configured for an 8 bit width. When the external data bus is configured for a 16 bit width, this pin becomes the high byte write strobe. 3 41 O A1: Address bit 1 of the external address bus. 4 42 O A2: Address bit 2 of the external address bus. 5 43 O A3: Address bit 3 of the external address bus. 6 44 I RxD1 (P1.4): Receiver input for serial port 1. 7 1 O TxD1 (P1.5): Transmitter output for serial port 1. 8 2 I/O T2 (P1.6): Timer/counter 2 external count input/clockout. 9 3 I T2EX (P1.7): Timer/counter 2 reload/capture/direction control P2.0 – P2.7 24–31 18–25 I/O Port 2: Port 2 is an 8-bit I/O port with a user-configurable output type. Port 2 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. The operation of port 2 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. When the external program/data bus is used in 16-bit mode, Port 2 becomes the multiplexed high data/instruction byte and address lines 12 through 19. When the external program/data bus is used in 8-bit mode, the number of address lines that appear on port 2 is user programmable. P3.0 – P3.7 11, 13–19 5, 7–13 I/O Port 3: Port 3 is an 8-bit I/O port with a user configurable output type. Port 3 latches have 1s written to them and are configured in the quasi-bidirectional mode during reset. the operation of port 3 pins as inputs and outputs depends upon the port configuration selected. Each port pin is configured independently. Refer to the section on I/O port configuration and the DC Electrical Characteristics for details. Port 3 also provides various special functions as described below. 11 5 I RxD0 (P3.0): Receiver input for serial port 0. 13 7 O TxD0 (P3.1): Transmitter output for serial port 0. 14 8 I INT0 (P3.2): External interrupt 0 input. 15 9 I INT1 (P3.3): External interrupt 1 input. 16 10 I/O T0 (P3.4): Timer 0 external input, or timer 0 overflow output. 17 11 I/O T1/BUSW (P3.5): Timer 1 external input, or timer 1 overflow output. The value on this pin is latched as the external reset input is released and defines the default external data bus width (BUSW). 0 = 8-bit bus and 1 = 16-bit bus. 18 12 O WRL (P3.6): External data memory low byte write strobe. 19 13 O RD (P3.7): External data memory read strobe. RST 10 4 I Reset: A low on this pin resets the microcontroller, causing I/O ports and peripherals to take on their default states, and the processor to begin execution at the address contained in the reset vector. Refer to the section on Reset for details. ALE/PROG 33 27 I/O Address Latch Enable/Program Pulse: A high output on the ALE pin signals external circuitry to latch the address portion of the multiplexed address/data bus. A pulse on ALE occurs only when it is needed in order to process a bus cycle. |
Similar Part No. - P51XAG33KBA |
|
Similar Description - P51XAG33KBA |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
