LH28F008SCR-L12 datasheet(10/55 Pages) SHARP

Part #	LH28F008SCR-L12

Description	Flash Memory 8M (1MB 횞 8)

Download	55 Pages

Scroll/Zoom	100%

Manufacturer	SHARP [Sharp Corporation]

Direct Link	http://sharp-world.com/

Logo

10 / 55 page

FFFFF

F0000

EFFFF

E0000

DFFFF

D0000

CFFFF

C0000

BFFFF

B0000

AFFFF

A0000

9FFFF

90000

8FFFF

80000

7FFFF

70000

6FFFF

60000

5FFFF

50000

4FFFF

40000

3FFFF

30000

2FFFF

20000

1FFFF

10000

0FFFF

00000

64K-byte Block

11

64K-byte Block

12

64K-byte Block

10

64K-byte Block

9

64K-byte Block

8

64K-byte Block

5

64K-byte Block

13

64K-byte Block

14

64K-byte Block

15

64K-byte Block

4

64K-byte Block

3

64K-byte Block

2

64K-byte Block

1

64K-byte Block

0

64K-byte Block

7

64K-byte Block

6

LHF08CH1

7

Rev. 1.3

2 PRINCIPLES OF OPERATION

The LH28F008SCT-L85 SmartVoltage Flash memory

includes an on-chip WSM to manage block erase,

byte write, and lock-bit configuration functions. It

allows for: 100% TTL-level control inputs, fixed power

supplies during block erasure, byte write, and lock-bit

configuration, and minimal processor overhead with

RAM-Like interface timings.

After initial device power-up or return from deep

power-down mode (see Bus Operations), the device

defaults to read array mode. Manipulation of external

memory control pins allow array read, standby, and

output disable operations.

Status register and identifier codes can be accessed

through the CUI independent of the VPP voltage. High

voltage on VPP enables successful block erasure,

byte writing, and lock-bit configuration. All functions

associated with altering memory contents−block

erase, byte write, Lock-bit configuration, status, and

identifier codes−are accessed via the CUI and

verified through the status register.

Commands

are

written

using

standard

microprocessor write timings. The CUI contents serve

as input to the WSM, which controls the block erase,

byte write, and lock-bit configuration. The internal

algorithms are regulated by the WSM, including pulse

repetition, internal verification, and margining of data.

Addresses and data are internally latch during write

cycles. Writing the appropriate command outputs

array data, accesses the identifier codes, or outputs

status register data.

Interface software that initiates and polls progress of

block erase, byte write, and lock-bit configuration can

be stored in any block. This code is copied to and

executed from system RAM during flash memory

updates. After successful completion, reads are

again possible via the Read Array command. Block

erase suspend allows system software to suspend a

block erase to read or write data from any other

block. Byte write suspend allows system software to

suspend a byte write to read data from any other

flash memory array location.

Figure 3. Memory Map

2.1 Data Protection

Depending on the application, the system designer

may

choose

to

make

the

VPP power supply

switchable

(available

only

when

memory

block

erases, byte writes, or lock-bit configurations are

required) or hardwired to VPPH1/2/3. The device

accommodates

either

design

practice

and

encourages optimization of the processor-memory

interface.

When VPP≤VPPLK, memory contents cannot be

altered. The CUI, with two-step block erase, byte

write, or lock-bit configuration command sequences,

provides protection from unwanted operations even

when high voltage is applied to VPP. All write

functions are disabled when VCC is below the write

lockout voltage VLKO or when RP# is at VIL. The

device’s block locking capability provides additional

protection from inadvertent code or data alteration by

gating erase and byte write operations.

sharp

Similar Part No. - LH28F008SCR-L12

Manufacturer	Part #	Datasheet	Description
Sharp Corporation	LH28F008SCR-85	3Mb / 47P	Flash Memory 8M (1M 횞8)

More results

Similar Description - LH28F008SCR-L12

Manufacturer	Part #	Datasheet	Description
Sharp Corporation	LH28F008SA	249Kb / 27P	8M (1M 횞 8) Flash Memory
	LH28F008SC	349Kb / 38P	8M (1M 횞 8) Flash Memory
	LHF16KA7	3Mb / 53P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF16KA3	2Mb / 58P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF16KA4	3Mb / 52P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF16KA9	3Mb / 52P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF16KA1	3Mb / 58P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF16KA6	2Mb / 59P	Flash Memory 16M (2MB 횞 8/1MB 횞 16)
	LHF80V07	2Mb / 42P	Flash Memory 8M (1M 횞 8/512K 횞 16)
	LH28F800SU	328Kb / 38P	8M (512K 횞 16, 1M 횞 8) Flash Memory

More results

LH28F008SCR-L12 Datasheet(PDF) 10 Page - Sharp Corporation

LH28F008SCR-L12 Datasheet(HTML) 10 Page - Sharp Corporation

Similar Part No. - LH28F008SCR-L12

Similar Description - LH28F008SCR-L12

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55

Datasheet Download

Link URL