Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

TDH2 Datasheet(PDF) 6 Page - List of Unclassifed Manufacturers

Part No. TDH2
Description  UHF Multi Channel Hi Power Radio Modem
Download  11 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  ETC2 [List of Unclassifed Manufacturers]
Homepage  
Logo 

TDH2 Datasheet(HTML) 6 Page - List of Unclassifed Manufacturers

Zoom Inzoom in Zoom Outzoom out
 6 / 11 page
background image
Radiometrix Ltd
TDH2 Data Sheet
page 6
Programming the TDH2
In order to use all the functions embedded in the TDH2, the user must be aware of the
setup/programming facility, which allow different addresses and frequency channels to be set up, and if
necessary accesses diagnostic test modes.
The TDH2 is programmed through the same RS232 port that is used for sending/receiving data. An
RS232 terminal emulator (such as Aterm or HyperTerminal) is an ideal tool.
To enter program mode, the SETUP pin must be pulled low. In this mode the radio link is disabled,
but characters sent (at 9600 baud, as normal) to the unit are echoed back on the RXD pin.
The unit will only respond to certain command strings:
ADDR0 to ADDR7 <CR>:
These commands set up one of 8 unique addresses.
CHAN0 to CHAN4 <CR>:
These commands select one of 5 preset channels
A TDH2 will only communicate with a unit set to the same address and the same channel.
Address and channel numbers are stored in volatile memory. On power-up the TDH2 reverts to the
default in EEPROM (as supplied this is always address 0 and Channel 0)
SETPROGRAM <CR>:
Writes the current address and current channel into EEPROM as the
new default.
A tilda character (~, ascii 126dec) sent by the unit indicates end of
EEPROM write sequence
(these commands are normally only used for factory diagnostics)
NOTONE <CR>:
Transmit unmodulated carrier
LFTONE <CR>:
Transmit carrier modulated with 8KHz squarewave
HFTONE <CR>:
Transmit carrier modulated with 16KHz squarewave
# <CR>:
Transmitter off
A Carriage Return ‘<CR>’ (00Dhex) should be entered after each command sequence to execute it.
Releasing the SETUP pin to high state returns the TDH2 to normal operation.
Interfacing a microcontroller to TDH2
Figure 6: TDH2 interfaced directly to a microcontroller
TDH2 can be directly interfaced to any microcontrollers. If the microcontroller has a built-in UART, it
can concentrate on its main task and leave the packet formatting, bit balancing and error checking of
serial data to TDH2.


Html Pages

1  2  3  4  5  6  7  8  9  10  11 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn