Dialight Corporation • 1501 Route 34 South • Farmingdale, NJ 07727 • TEL: (732) 919-3119 • FAX: (732) 751-5778 •www.dialight.com

3 x 5mm Rectangular

®

Optical Light Pipe, 2 Array (RJ45 Jack)

515-1070

19.05

[.750]

13.98

[.550]

2.54

[.100]

5.08

[.200]

2 PLCS

3.05

[.120]

1.91

[.075]

C.L. LEDS

27.94

[1.100]

35.26

[1.388]

3.66

[.144]

.71

[.028]

1.50

[.059]

.99

[.039]

.99

[.039]

2.01

[.079]

1.57

[.062]

1.35

[.053]

13.98

[.550]

6.99

[.275]

27.94

±.05

[1.100

±.002]

2XØ 2.87

±.05

[.113

±.002]

RECOMMENDED SOLD

ER P

AD/HOLES LA

YOUT

FOR BI-COLOR LED

S

C.L. MOUNTIN

G

PIN #1

3.56

[.140]

20.57

[.81]

31.24

[1.23]

DIFFUSED

FRONT

SURF

ACE

27.43

[1.080]

7.62

±.15

[.300

±.006]

1.57

[.062]

DIRECTIO

N

OF LIGHT

3.93

[.155]

29.0

[1.142]

FRONT

PANEL

Dimensions in mm [inches]

Recommended

MicroLED SMT LEDs

for use with 515-1070

PART NO.

COLOR

PAGE #

597-3001-1xx

Red

1-19

597-3111-1xx

AlGaAs Red

1-19

597-3111-5xx

AlGaAs Red

1-30

597-3211-1xx

Orange

1-19

597-3211-5xx

Orange

1-30

597-3301-1xx

Green

1-19

597-3301-5xx

Green

1-30

597-3401-1xx

Yellow

1-19

597-3401-5xx

Yellow

1-30

597-7701-1xx

Red/Green

1-20

597-7701-5xx

Red/Green

1-31

597-7721-1xx

Yellow/Green

1-20

597-7721-5xx

Yellow/Green

1-31

597-7731-1xx

Red/Yellow

1-20

Features

• Complements Dialight’s 515-1022 Four Array Optopipe

Light Pipe

• Allows indicators to be positioned above corresponding

RJ45 jack or D-Subminiature

• High transmissivity polycarbonate material

• UL94V-0 compliance

• ESD protection (circuit isolation from front panel)

• Wide viewing angle

• Arrays reduce insertion costs

• Secures to PCB by press-fit

LED Data

For absolute maximum ratings and other electri-

cal and optical data on the recommended LEDs,

refer to LED data sheets.

Dialight Optopipe

This light pipe’s two 3 x 5mm rectangular light emitting surfaces appear bright and are optically well isolated. The light

pipe is reliably held in place by 2 press-fit pins located at either end of the light pipe array. This Optopipe

through-the-case indicator by conducting the light over the top of connectors or switches. A textured finish on the 2 light

emitting surfaces maximizes the viewing angle. The recommended light sources are Dialight's 597 Series PLCC-2 or

PLCC-4 Type SMT LEDs. The LEDs are mounted in a straight line on an 0.550" pitch. The light pipe material is water clear

transmissive polycarbonate rated UL94-V0, and has a 35% oxygen index.

Dialight can provide custom Optopipe

Operating/Storage Temperature

–30°C to +100°C

NOTE: designed for

post-reflow

PC board insertion.