 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
XR19L210 Datasheet(PDF) 4 Page - Exar Corporation |
|
||||||||||||||||||||||||||||||
XR19L210 Datasheet(HTML) 4 Page - Exar Corporation |
|
|
4 / 43 page  XR19L210 4 SINGLE CHANNEL INTEGRATED UART AND RS-232 TRANSCEIVER REV. 1.0.1 NOTE: Pin type: I=Input, O=Output, I/O= Input/output, OD=Output Open Drain. For CMOS/TTL Voltage levels, ’LOW’ indicates a voltage in the range 0V to VIL and ’HIGH" indicates a voltage in the range VIH to VCC. For RS-232 input voltage levels, ’LOW’ is any voltage < -3V and ’HIGH’ is any voltage > 3V. For RS-232 output voltage levels, ’LOW’ is any voltage < -5V and ’HIGH’ is any voltage > 5V. PwrSave 13 I Power-Save (active high). This feature isolates the L210’s data bus interface from the host preventing other bus activities that cause higher power drain during sleep mode. See Sleep Mode with Auto Wake-up and Power-Save Feature section for details. ACP 16 I Autosleep for Charge Pump (active HIGH). When this pin is HIGH, the charge pump is shut off if the L210 is already in partial sleep mode, i.e. the crystal oscillator is stopped. I/M# 4 I Intel or Motorola Bus Select. When I/M# pin is HIGH, 16 or Intel Mode, the device will operate in the Intel bus type of interface. When I/M# pin is LOW, 68 or Motorola mode, the device will operate in the Motorola bus type of interface. RESET (RESET#) 28 I When I/M# pin is HIGH for Intel bus interface, this input becomes RESET (active high). When I/M# pin is LOW for Motorola bus interface, this input becomes RESET# (active low). A 40 ns minimum active pulse on this pin will reset the internal registers and all outputs of the UART. The UART transmitter output will be held HIGH, the receiver input will be ignored and outputs are reset during reset period (see Table 11). C2+ C2- 20 21 - Charge pump capacitors. As shown in Figure 1, a 0.1 uF capacitor should be placed between these 2 pins. C1+ C1- 29 30 - Charge pump capacitors. As shown in Figure 1, a 0.1 uF capacitor should be placed between these 2 pins. VREF+ 32 Pwr +5.0V generated by the charge pump. VREF- 22 Pwr -5.0V generated by the charge pump. VCC 33 Pwr 3.0V to 5.5V power supply. All CMOS/TTL input pins, except XTAL1, are 5V tolerant. GND 6, 18, 27 Pwr Power supply common, ground. - PAD Pwr The center pad on the backside of the 40-QFN package is metallic and is not electrically connected to anything inside the device. It must be soldered on to the PCB and may be optionally connected to GND on the PCB. The thermal pad size on the PCB should be the approximate size of this center pad and should be solder mask defined. The solder mask opening should be at least 0.0025" inwards from the edge of the PCB thermal pad. NC 3, 12, 31, 39, 40 - No Connect. Note that in Motorola mode, the IOR# pin also becomes an NC pin. Pin Descriptions NAME 40-QFN PIN# TYPE DESCRIPTION |
Similar Part No. - XR19L210_07 |
|
Similar Description - XR19L210_07 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
