Electronic Components Datasheet Search |
|
XR16V2751IM Datasheet(PDF) 4 Page - Exar Corporation |
|
XR16V2751IM Datasheet(HTML) 4 Page - Exar Corporation |
4 / 52 page XR16V2751 4 HIGH PERFORMANCE DUART WITH 64-BYTE FIFO AND POWERSAVE FEATURE REV. 1.0.0 INTB 29 O UART channel B Interrupt output. The output state is defined by the user through the software setting of MCR[3]. INTB is set to the active mode and OP2B# output LOW when MCR[3] is set to a logic 1. INTB is set to the three state mode and OP2B# out- put HIGH when MCR[3] is set to a logic 0 (default). See MCR[3]. TXRDYA# 43 O UART channel A Transmitter Ready (active low). The output provides the TX FIFO/ THR status for transmit channel A. See Table 3. If it is not used, leave it uncon- nected. RXRDYA# 31 O UART channel A Receiver Ready (active low). This output provides the RX FIFO/ RHR status for receive channel A. See Table 3. If it is not used, leave it uncon- nected. TXRDYB# 6 O UART channel B Transmitter Ready (active low). The output provides the TX FIFO/ THR status for transmit channel B. See Table 4. If it is not used, leave it uncon- nected. RXRDYB# 18 O UART channel B Receiver Ready (active low). This output provides the RX FIFO/ RHR status for receive channel B. See Table 3. If it is not used, leave it uncon- nected. MODEM OR SERIAL I/O INTERFACE TXA 7 O UART channel A Transmit Data or infrared encoder data. Standard transmit and receive interface is enabled when MCR[6] = 0. In this mode, the TX signal will be HIGH during reset or idle (no data). Infrared IrDA transmit and receive interface is enabled when MCR[6] = 1. In the Infrared mode, the inactive state (no data) for the Infrared encoder/decoder interface is LOW. If it is not used, leave it unconnected. RXA 5 I UART channel A Receive Data or infrared receive data. Normal receive data input must idle HIGH. The infrared receiver pulses typically idles at LOW but can be inverted by software control prior going in to the decoder, see MCR[6] and FCTR[2]. If this pin is not used, tie it to VCC or pull it high via a 100k ohm resistor. RTSA# 33 O UART channel A Request-to-Send (active low) or general purpose output. This out- put must be asserted prior to using auto RTS flow control, see EFR[6], MCR[1], FCTR[1:0], EMSR[5:4] and IER[6]. For auto RS485 half-duplex direction control, see FCTR[3] and EMSR[3]. CTSA# 38 I UART channel A Clear-to-Send (active low) or general purpose input. It can be used for auto CTS flow control, see EFR[7], and IER[7]. This input should be con- nected to VCC when not used. DTRA# 34 O UART channel A Data-Terminal-Ready (active low) or general purpose output. If it is not used, leave it unconnected. DSRA# 39 I UART channel A Data-Set-Ready (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. CDA# 40 I UART channel A Carrier-Detect (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. RIA# 41 I UART channel A Ring-Indicator (active low) or general purpose input. This input should be connected to VCC when not used. This input has no effect on the UART. Pin Description NAME 48-TQFP PIN # TYPE DESCRIPTION |
Similar Part No. - XR16V2751IM |
|
Similar Description - XR16V2751IM |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |