![]() |
Electronic Components Datasheet Search |
|
TRF3701 Datasheet(PDF) 5 Page - Texas Instruments |
|
TRF3701 Datasheet(HTML) 5 Page - Texas Instruments |
5 / 31 page ![]() www.ti.com RF OUTPUT PERFORMANCE (340 MHz) RF OUTPUT PERFORMANCE (140 MHz) TRF3701 SLWS145D – FEBRUARY 2003 – REVISED AUGUST 2006 Over recommended operating conditions, VCC = 5 V, VCM = 3.7 V, f LO = 340 MHz at 0 dBm, TA = 25°C (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Single and Two-Tone Specifications Output power –1 dBm Second baseband –52 dBc harmonic (USB or LSB)(3) I, Q(2) = 1 Vp-p, fBB = 928 kHz Third baseband harmonic –45 dBc (USB or LSB)(3) I, Q(2) = 1 Vp-p (two-tone signal, fBB1 = 928 kHz, IMD3 67 dBc fBB2 = 992 kHz) P1dB (output compression 6 dBm point) I, Q(2) = 1 Vp-p, fBB = 928 kHz, unadjusted 40 51 Carrier suppression dBc I, Q(2) = 1 Vp-p, fBB = 928 kHz, optimized >60 I, Q(2) = 1 Vp-p, fBB = 928 kHz, unadjusted 35 Sideband suppression dBc I, Q(2) = 1 Vp-p, fBB = 928 kHz, optimized >60 (1) Baseband inputs are differential; equivalent performance is attained by using single-ended drive. (2) I , Q = 1 Vp-p implies that the magnitude of the signal at each input pin IVIN, IREF, QVIN, QREF is equal to 500 mVp-p. (3) USB = upper sideband. LSB = lower sideband. Over recommended operating conditions, VCC = 5 V, VCM = 3.7 V, f LO = 140 MHz at 0 dBm, TA = 25°C (unless otherwise noted)(1) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT Single and Two-Tone Specifications Output power –1 dBm Second baseband –61.5 dBc harmonic (USB or LSB)(3) I, Q(2) = 1 Vp-p, fBB = 928 kHz Third baseband harmonic -46 dBc (USB or LSB)(3) I, Q(2) = 1 Vp-p (two-tone signal, fBB1 = 928 kHz, IMD3 68 dBc fBB2 = 992 kHz) P1dB (output compression 3.6 dBm point) I, Q(2) = 1 Vp-p, fBB = 928 kHz, unadjusted 40 50 Carrier suppression dBc I, Q(2) = 1 Vp-p, fBB = 928 kHz, optimized >60 I, Q(2) = 1 Vp-p, fBB = 928 kHz, unadjusted 35 Sideband suppression dBc I, Q(2) = 1 Vp-p, fBB = 928 kHz, optimized >60 (1) Baseband inputs are differential; equivalent performance is attained by using single-ended drive. (2) I , Q = 1 Vp-p implies that the magnitude of the signal at each input pin IVIN, IREF, QVIN, QREF is equal to 500 mVp-p. (3) USB = upper sideband. LSB = lower sideband. 5 Submit Documentation Feedback |