LP211, LP311

LOW POWER DIFFERENTIAL COMPARATORS

WITH STROBES

SLCS003D − JUNE 1987 − REVISED SEPTEMBER 2003

2

POST OFFICE BOX 655303

functional block diagram

EMIT OUT

COL OUT

IN+

IN−

BAL/STRB

BALANCE

18 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

−18 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±30 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

±15 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

30 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

40 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Voltage from collector output to emitter output

40 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Duration of output short circuit (see Note 4)

40 V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Package thermal impedance,

97

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

P package

85

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

PS package

95

°C/W

. . . . . . . . . . . . . . . . . . . . . . . . . . .

150

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

−65

°C to 150°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

† Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and

functional operation of the device at these or any other conditions beyond those indicated in the recommended operating conditions section of this

specification is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

NOTES:

1. All voltage values, unless otherwise noted, are with respect to the midpoint between VCC+ and VCC−.

2. Differential input voltages are at IN+ with respect to IN−.

3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage of

±15 V, whichever is less.

4. The output may be shorted to ground or to either power supply.

6. The package thermal impedance is calculated in accordance with JESD 51-7.

recommended operating conditions

MIN

MAX

UNIT

(|VCC±| ≤ 15 V)

Input voltage

VCC− + 0.5

VCC+ − 1.5

V

VCC+ − VCC−

Supply voltage

3.5

30

V