Electronic Components Datasheet Search
  English  ▼

Delete All
ON OFF
ALLDATASHEET.COM

X  

Preview PDF Download HTML

GC3021A Datasheet(PDF) 5 Page - Texas Instruments

Part No. GC3021A
Description  3.3V MIXER AND CARRIER REMOVAL CHIP
Download  38 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  TI [Texas Instruments]
Homepage  http://www.ti.com
Logo 

GC3021A Datasheet(HTML) 5 Page - Texas Instruments

 
Zoom Inzoom in Zoom Outzoom out
 5 / 38 page
background image
Texas Instruments Incorporated
- 3 -
GC3021A 3.3V MIXER AND CARRIER REMOVAL CHIP
SLWS137A
This document contains information which may be changed at any time without notice
or DSP chip) can write into a register by setting A[0:8] to the desired register address, setting the CE pin
low, setting C[0:15] to the desired value and then pulsing WE low. RE must remain high.
To read from a control register the processor must set A[0:8] to the desired address, set CE low,
and then set RE low. The chip will then drive C[0:15] with the contents of the selected register. After the
processor has read the value from C[0:15] it should set RE and CE high. The C[0:15] pins are turned off
(high impedance) whenever CE is high or WE is low. The chip will only drive these pins when both CE and
RE are low and WE is high.
If RE is held low, then the interface will behave in the GC3021 mode, where CE is CS, and WE is
R/W.
The chip’s control address space is divided into fourteen control registers, a test port, four DC offset
registers, 256 phase error memory words, and 256 snapshot memory words. The 14 control registers are
MODE_REG, SYNC_REG0, SYNC_REG1, DELAY_REG, COUNTER_REG, PLL_REG, FREQ_REG0,
FREQ_REG1, OUTPUT_REGA, OUTPUT_REGB, OUTPUT_REGC, OUTPUT_REGD, SNAP_REG, and
PHASE_REG. The control registers are mapped to addresses 0 to 13. See Section 4.0 for details about the
contents of these registers.
Address 14 is used to generate a one-shot pulse. This pulse, OS, which is one clock cycle wide,
can be output from the chip on the SO pin or used to synchronize internal circuits. Address 15 is a read only
port used to monitor the power-down and keepalive clock functions for test. Addresses 16 through 19 are
the DC offset registers DC_I_IN, DC_Q_IN, DC_I_OUT, DC_Q_OUT.
Addresses 20 through 255 are unused.
Addresses 256 through 511 are shared between the phase error memory and the snapshot
memory. Reading from these addresses accesses the contents of the snapshot memory. Writing to these
addresses loads the phase error lookup memory.
2.2
SYNC COUNTER
The sync counter circuit is used to generate sync pulses for the chip. The circuit accepts two sync
inputs (SA and SB) and generates internal syncs and a sync out (SO) pulse. The circuit contains a 20 bit
counter which can be set to count in cycles of 16*(COUNT+1) clocks, where COUNT ranges from 0 to 216-1.
The counter’s terminal count (TC) can be used as a synchronization pulse. The lower 12 bits from the
counter are used as input data during diagnostics.
The circuit can generate a one-shot pulse (OS) which can be used as a synchronization pulse.
The input syncs SA and SB can be delayed by up to 258 clock cycles. The delayed syncs (DSA and
DSB) can be used to adjust the sync timing to meet system requirements.
The internal syncs are used to synchronize the counter, the symbol align circuit, the snapshot
memory, the phase lock loop circuit and NCO circuit. Each circuit can be independently synchronized to SA,
SB, DSA, DSB, TC, OS, or left to free run. The sync output can also be chosen from these syncs.


Html Pages

1  2  3  4  5  6  7  8  9  10  11  12  13  14  15  16  17  18  19  20  21  22  23  24  25  26  27  28  29  30  31  32  33  34  35  36  37  38 


Datasheet Download




Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Alldatasheet API   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn