100 Watt

Isolated

Dual Output

INNOLINE

DC/DC-Converter

RP100-

S_DI

Series

Dual Outputs Total Power up to 100W

Features

Selection Guide

Notes:

Part

Input

Output

Output

Line

Load

Input

Efficiency

Number

Voltage

Voltage

Current

Regulation Regulation

Current

(8)

(9)

Single Output

(VDC)

(VDC)

(A)

(mV)

(mV)

(A)

%

RP100-481.8S

36 – 75

1.8

25

4

6

1157

86

RP100-482.5S

36 – 75

2.5

25

5

8

1608

87

RP100-483.3S

36 – 75

3.3

25

7

10

2022

90

RP100-4805S

36 – 75

5

20

10

15

2480

90

RP100-4815S

36 – 75

15

6.66

30

45

2507

90

Part

Input

Output

Output

Line

Load

Input Efficiency

Number

Voltage

Voltage

Current

Regulation

Regulation Current

(8)

(9)

V1 / V2

I1 / I2

V1 / V2

V1 / V2

Dual Output

(VDC)

(VDC)

(A)

(mV)

(mV)

(A)

%

RP100-483.305DI

36 – 75

5 / 3.3

20 / 25

25 / 16.5

25 / 16.5

2.39

87

RP100-482.505DI

36 – 75

5 / 2.5

20 / 25

25 / 12.5

25 / 12.5

2.45

85

RP100-482.53.3DI 36 – 75

3.3 / 2.5

25 / 25

16.5 / 12.5

16.5 / 12.5

2.44

85

1. Maximum output deviation is 10% inclusive of remote sense. If remote sense is not being used,

the +Vsense should be connected to its corresponding +Vout and likewise the -Vsense should be connected

to its corresponding -Vout.

2. Single: Measured with a 1µF M/C and a 10µF T/C.

Dual: For each outputs.

3. An external filter capacitor is required for normal operation.

The capacitor should be capable of handing 1A ripple current for 48V models.

RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90m

4. Single: The negative / positive logic and length are optional ( see table ).

The pin voltage is referenced to negative input.

Dual: The ON/OFF control function. There are positive logic ( standard ) and negative logic ( option ).

The pin voltage is referenced to negative input.

To order negative logic ON/OFF control add the suffix-N. ( Ex:RP100-483.305I/N )

5. BELLCORE TR-NWT-000332. Case I: 50% Stress, Temperature at 40°C.

( Ground fixed and controlled environment )

6. Heat sink is optional and P/N: 7G-0021, 7G-0022, 7G-0023, 7G-0024.

7. The RP100 meets level A and level B conducted emissions only with external components connected before

the input pin to the converter.

8. Maximum value at nominal input voltage and full load.

9. Typical value at nominal input voltage and full load.

The dual efficiency test condition:

RP100-483.305DI

@

5V/12A and 3.3V/12A

RP100-482.505DI

@

5V/12A and 2.5V/16A

RP100-482.53.3DI @ 3.3V/18A and 2.5V/16A

10. BASEPLATE GROUNDING: Base-plate should be grounded at one of four screw bolts prior to operation.

11. The converter is provided by basic insulation.

12. “N

N” for Negative remote ON/OFF.

13. “P

P” for Positive remote ON/OFF.

July-2006

195

www.recom-international.com