Electronic Components Datasheet Search 

UC2843BDR2G Datasheet(PDF) 8 Page  ON Semiconductor 

UC2843BDR2G Datasheet(HTML) 8 Page  ON Semiconductor 
8 / 25 page UC3842B, UC3843B, UC2842B, UC2843B www.onsemi.com 8 OPERATING DESCRIPTION The UC3842B, UC3843B series are high performance, fixed frequency, current mode controllers. They are specifically designed for Off−Line and DC−to−DC converter applications offering the designer a cost−effective solution with minimal external components. A representative block diagram is shown in Figure 19. Oscillator The oscillator frequency is programmed by the values chosen for the timing components RT and CT. It must also be noted that the value of RT uniquely determines the maximum duty ratio of UC384xx. The oscillator configuration depicting the connection of the timing components to the RT/CT pin of the controller is shown in Figure 18. Capacitor CT gets charged from the Vref source, through resistor RT to its peak threshold VRT/CT(peak), typically 2.8 V. Upon reaching this peak threshold volage, an internal 8.3 mA current source, Idischg, is enabled and the voltage across CT begins to decrease. Once the voltage across CT reaches its valley threshold, VRT/CT(valley), typically 1.2 V, Idischg turns off. This allows capacitor CT to charge up again from Vref. This entire cycle repeats, and the resulting waveform on the RT/CT pin has a sawtooth shape. Typical waveforms are shown in Figure 20. The oscillator thresholds are temperature compensated to within ±6% at 50 kHz . Considering the general industry trend of operating switching controllers at higher frequencies, the UC384xx is guaranteed to operate within ±10% at 250 kHz. These internal circuit refinements minimize variations of oscillator frequency and maximum duty ratio. The charging and discharging times of the timing capacitor CT are calculated using Equations 1 and 2. These equations do not take into account the propagation delays of the internal comparator. Hence, at higher frequencies, the calculated value of the oscillator frequency differs from the actual value. t RT CT(chg) + RTCT ln VRT CT(valley) * Vref V RT CT(peak) * Vref (eq. 1) t RT CT(dischg) + RTCT ln RTIdischg ) VRT CT(peak) * Vref RTIdischg ) VRT CT(valley) * Vref (eq. 2) The maximum duty ratio, Dmax is given by Equation 3. Dmax + t RT CT(chg) t RT CT(chg) ) tRT CT(dischg) (eq. 3) Substituting Equations 1 and 2 into Equation 3, and after algebraic simplification, we obtain Dmax + ln VRT CT(valley)*Vref VRT CT(peak)*Vref ln VRT CT(valley)*Vref VRT CT(peak)*Vref @ RTIdischg)VRT CT(peak)*Vref RTIdischg)VRT CT(valley)*Vref (eq. 4) Clearly, the maximum duty ratio is determined by the timing resistor RT. Therefore, RT is chosen such as to achieve a desired maximum duty ratio. Once RT has been selected, CT can now be chosen to obtain the desired switching frequency as per Equation 5. f + 1 RTCT ln VRT CT(valley)*Vref VRT CT(peak)*Vref @ RTIdischg)VRT CT(peak)*Vref RTIdischg)VRT CT(valley)*Vref (eq. 5) Figure 2 shows the frequency and maximum duty ratio variation versus RT for given values of CT. Care should be taken to ensure that the absolute minimum value of RT should not be less than 542 W. However, considering a 10% tolerance for the timing resistor, the nearest available standard resistor of 680 W is the absolute minimum that can be used to guarantee normal oscillator operation. If a timing resistor smaller than this value is used, then the charging current through the RT, CT path will exceed the pulldown (discharge) current and the oscillator will get permanently locked/latched to an undefined state. In many noisesensitive applications it may be desirable to frequencylock the converter to an external system clock. This can be accomplished by applying a clock signal to the circuit shown in Figure 22. For reliable synchronization, the freerunning oscillator frequency should be set about 10% less than the clock frequency. A method for multiunit synchronization is shown in Figure 23. By tailoring the clock waveform, accurate Output duty ratio clamping can be achieved. Enable Idischg Vref RT/CT RT CT 2.8 V 1.2 V Figure 18. Oscillator Configuration 
Similar Part No.  UC2843BDR2G 

Similar Description  UC2843BDR2G 


Link URL 
Privacy Policy 
ALLDATASHEET.COM 
Does ALLDATASHEET help your business so far? [ DONATE ] 
About Alldatasheet  Advertisement  Datasheet Upload  Contact us  Privacy Policy  Link Exchange  Manufacturer List All Rights Reserved©Alldatasheet.com 
Russian : Alldatasheetru.com  Korean : Alldatasheet.co.kr  Spanish : Alldatasheet.es  French : Alldatasheet.fr  Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com  Polish : Alldatasheet.pl  Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in  Mexican : Alldatasheet.com.mx  British : Alldatasheet.co.uk  New Zealand : Alldatasheet.co.nz 
Family Site : ic2ic.com 
icmetro.com 