Electronic Components Datasheet Search |
|
ICS348R-22T Datasheet(PDF) 4 Page - Integrated Circuit Systems |
|
ICS348R-22T Datasheet(HTML) 4 Page - Integrated Circuit Systems |
4 / 8 page Quad PLL Field Programmable VersaClock Synthesizer MDS 348-22 A 4 Revision 120704 Integrated Circuit Systems, Inc. ● 525 Race Street, San Jose, CA 95126 ● tel (408) 297-1201 ● www.icst.com ICS348-22 PRELIMINARY INFORMATION External Components Series Termination Resistor Clock output traces over one inch should use series termination. To series terminate a 50 Ω trace (a commonly used trace impedance), place a 33 Ω resistor in series with the clock line, as close to the clock output pin as possible. The nominal impedance of the clock output is 20 Ω. Decoupling Capacitors As with any high-performance mixed-signal IC, the ICS348-22 must be isolated from system power supply noise to perform optimally. Decoupling capacitors of 0.01µF must be connected between each VDD and the PCB ground plane. Crystal Load Capacitors The device crystal connections should include pads for small capacitors from X1 to ground and from X2 to ground. These capacitors are used to adjust the stray capacitance of the board to match the nominally required crystal load capacitance. Because load capacitance can only be increased in this trimming process, it is important to keep stray capacitance to a minimum by using very short PCB traces (and no vias) been the crystal and device. Crystal capacitors must be connected from each of the pins X1 and X2 to ground. The value (in pF) of these crystal caps should equal (CL -6 pF)*2. In this equation, CL= crystal load capacitance in pF. Example: For a crystal with a 16 pF load capacitance, each crystal capacitor would be 20 pF [(16-6) x 2] = 20. PCB Layout Recommendations For optimum device performance and lowest output phase noise, the following guidelines should be observed. 1) Each 0.01µF decoupling capacitor should be mounted on the component side of the board as close to the VDD pin as possible. No vias should be used between decoupling capacitor and VDD pin. The PCB trace to VDD pin should be kept as short as possible, as should the PCB trace to the ground via. 2) The external crystal should be mounted just next to the device with short traces. The X1 and X2 traces should not be routed next to each other with minimum spaces, instead they should be separated and away from other traces. 3) To minimize EMI, the 33 Ω series termination resistor, if needed, should be placed close to the clock output. 4) An optimum layout is one with all components on the same side of the board, minimizing vias through other signal layers ICS348 Configuration Capabilities The architecture of the ICS348-22 allows the user to easily configure the device to a wide range of output frequencies, for a given input reference frequency. The frequency multiplier PLL provides a high degree of precision. The M/N values (the multiplier/divide values available to generate the target VCO frequency) can be set within the range of M = 1 to 2048 and N = 1 to 1024. The ICS348-22 also provides separate output divide values, from 2 through 20, to allow the two output clock banks to support widely differing frequency values from the same PLL. Each output frequency can be represented as: ICS VersaClock Software ICS applies years of PLL optimization experience into a user friendly software that accepts the user’s target reference clock and output frequencies and generates the lowest jitter, lowest power configuration, with only a press of a button. The user does not need to have prior PLL experience or determine the optimal VCO frequency to support multiple output frequencies. VersaClock software quickly evaluates accessible VCO frequencies with available output divide values and provides an easy to understand, bar code rating for the target output frequencies. The user may evaluate output accuracy, performance trade-off scenarios in seconds. OutputFreq REFFreq OutputDivide -------------------------------------- M N ----- ⋅ = |
Similar Part No. - ICS348R-22T |
|
Similar Description - ICS348R-22T |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |