Electronic Components Datasheet Search |
|
IDT723673 Datasheet(PDF) 4 Page - Integrated Device Technology |
|
IDT723673 Datasheet(HTML) 4 Page - Integrated Device Technology |
4 / 29 page 4 COMMERCIALTEMPERATURERANGE IDT723653/723663/723673 CMOS SyncFIFOTM WITH BUS-MATCHING 2,048 x 36 x 2, 4,096 x 36 x 2 and 8,192 x 36 x 2 PIN DESCRIPTIONS Symbol Name I/O Description A0-A35 Port A Data I/O 36-bit bidirectional data port for side A. AE Almost-EmptyFlag O Programmable Almost-Empty flag synchronized to CLKB. It is LOW when the number of words in the (Port B) FIFO is less than or equal to the value in the Almost-Empty B offset register, X. AF Almost-FullFlag O Programmable Almost-Full flag synchronized to CLKA. It is LOW when the number of empty (Port A) locations in the FIFO is less than or equal to the value in the Almost-Full A offset register, Y. B0-B35 Port B Data I/O 36-bit bidirectional data port for side B. BE/ FWFT Big-Endian/ I This is a dual purpose pin. During Master Reset, a HIGH on BE will select Big-Endian operation. In First Word this case, depending on the bus size, the most significant byte or word written to Port A is read from Fall Through Port B first. A LOW on BE will select Little-Endian operation. In this case, the least significant byte or word written to Port A is read from Port B first. After Master Reset, this pin selects the timing mode. A HIGH on FWFT selects IDT Standard mode, a LOW selects First Word Fall Through mode. Once the timing mode has been selected, the level on FWFT must be static throughout device operation. BM(1) Bus-MatchSelect I A HIGH on this pin enables either byte or word bus width on Port B, depending on the state of (Port B) SIZE. A LOW selects long word operation. BM works with SIZE and BE to select the bus size and endian arrangement for Port B.The level of BM must be static throughout device operation. CLKA Port A Clock I CLKA is a continuous clock that synchronizes all data transfers through Port A and can be asynchronous or coincident to CLKB. FF/IR and AF are synchronized to the LOW-to-HIGH transition of CLKA. CLKB Port B Clock I CLKB is a continuous clock that synchronizes all data transfers through Port B and can be asynchronous or coincident to CLKA. EF/OR and AE are synchronized to the LOW-to-HIGH transition of CLKB. CSA Port A Chip I CSA must be LOW to enable to LOW-to-HIGH transition of CLKA to read or write on Port A.The Select A0-A35 outputs are in the high-impedance state when CSA is HIGH. CSB Port B Chip I CSB must be LOW to enable a LOW-to-HIGH transition of CLKB to read or write data on Port B. Select The B0-B35 outputs are in the high-impedance state when CSB is HIGH. EF/OR Empty/Output O This is a dual function pin. In the IDT Standard mode, the EF function is selected. EFindicates Ready Flag whether or not the FIFO memory is empty. In the FWFT mode, the OR function is selected. OR indicates (Port B) the presence of valid data on the B0-B35 outputs, available for reading. EF/OR is synchronized to the LOW-to-HIGH transition of CLKB. ENA Port A Enable I ENA must be HIGH to enable a LOW-to-HIGH transition of CLKA to read or write data on Port A. ENB Port B Enable I ENB must be HIGH to enable a LOW-to-HIGH transition of CLKB to read or write data on Port B. FF/IR Full/Input O This is a dual function pin. In the IDT Standard mode, the FF function is selected. FF indicates Ready Flag whether or not the FIFO memory is full. In the FWFT mode, the IR function is selected. IR indicates (Port A) whether or not there is space available for writing to the FIFO memory. FF/IR is synchronized to the LOW-to-HIGH transition of CLKA. FS0/SD Flag Offset Select 0/ I FS1/ SEN and FS0/SD are dual-purpose inputs used for flag offset register programming. During Serial Data, Reset, FS1/ SEN andFS0/SD,togetherwithFS2selecttheflagoffsetprogrammingmethod. Three offset register programming methods are available: automatically load one of five preset values (8, 16, 64, 256 or 1,024), parallel load from Port A, and serial load. FS1/ SEN Flag Offset Select 1/ I Serial Enable When serial load is selected for flag offset register programming, FS1/ SEN is used as an enable synchronous to the LOW-to-HIGH transition of CLKA. When FS1/ SEN is LOW, a rising edge on FS2(1) Flag Offset Select 2 I CLKA load the bit present on FS0/SD into the X and Y registers. The number of bit writes required to program the offset registers is 22 for the IDT723653, 24 for the IDT723663, and 26 for the IDT723673. The first bit write stores the Y-register MSB and the last bit write stores the X-register LSB. MBA Port A Mailbox I A HIGH level on MBA chooses a mailbox register for a Port A read or write operation. Select MBB Port B Mailbox I A HIGH level on MBB chooses a mailbox register for a Port B read or write operation. When the Select B0-B35 outputs are active, a HIGH level on MBB selects data from the mail1 register for output and a LOW level selects FIFO data for output. |
Similar Part No. - IDT723673 |
|
Similar Description - IDT723673 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |