Electronic Components Datasheet Search |
|
IDT71P72804S200BQ Datasheet(PDF) 11 Page - Integrated Device Technology |
|
IDT71P72804S200BQ Datasheet(HTML) 11 Page - Integrated Device Technology |
11 / 22 page 6.42 11 IDT71P72204 (2M x 8-Bit), 71P72104 (2M x 9-Bit), 71P72804 (1M x 18-Bit) 71P72604 (512K x 36-Bit) Advance Information 18 Mb QDR II SRAM Burst of 2 Commercial Temperature Range DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 1.8 ± 100mV, VDDQ = 1.4V to 1.9V) Parameter Symbol Test Conditions Min Max Unit Note Input Leakage Current IIL VDD = Max VIN = VSS to VDDQ -10 +10 µA Output Leakage Current IOL Output Disabled -10 +10 µA Operating Current (x36,x18,x9,x8): DDR IDD VDD = Max, IOUT = 0mA (outputs open), Cycle Time > tKHKH Min 250MHZ - TBD mA 1 200MHZ - TBD 167MHZ - TBD Standby Current: NOP ISB1 Device Deselected (in NOP state), Iout = 0mA (outputs open), f=Max, All Inputs <0.2V or > VDD -0.2V 250MHZ - TBD mA 2 200MHZ - TBD 167MHZ - TBD Output High Voltage VOH1 RQ = 250 Ω, IOH = -15mA VDDQ/2-0.12 VDDQ/2+0.12 V 3,7 Output Low Voltage VOL1 RQ = 250 Ω, IOL = 15mA VDDQ/2-0.12 VDDQ/2+0.12 V 4,7 Output High Voltage VOH2 IOH = -0.1mA VDDQ-0.2 VDDQ V 5 Output Low Voltage VOL2 IOL = 0.1mA VSS 0.2 V 6 6109 tbl 10c NOTES: 1. Operating Current is measured at 100% bus utilization. 2. Standby Current is only after all pending read and write burst operations are completed. 3. Outputs are impedance-controlled. IOH = -(VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175 Ω < RQ < 350Ω. This parameter is tested at RQ = 250 Ω, which gives a nominal 50Ω output impedance. 4. Outputs are impedance-controlled. IOL = (VDDQ/2)/(RQ/5) and is guaranteed by device characterization for 175 Ω < RQ < 350Ω. This parameter is tested at RQ = 250 Ω, which gives a nominal 50Ω output impedance. 5. This measurement is taken to ensure that the output has the capability of pulling to the VDDQ rail, and is not intended to be used as an impedance measurement point. 6. This measurement is taken to ensure that the output has the capability of pulling to Vss, and is not intended to be used as an impedance measurement point. 7. Programmable Impedance Mode. |
Similar Part No. - IDT71P72804S200BQ |
|
Similar Description - IDT71P72804S200BQ |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |