CAGE CODE No. 18076

REV

N/C

01/30/09

MS9101

THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST A

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRESIDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

BRACKET, ANGLE 90°, .190 BOLT

PART NUMBER

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

.500

422

.200

.210

.068

.056

R

.210

.200

R .500

.250

.288

.278

.288/.278

MARK PART

NUMBER AND

MFR IDENT PER

AS 478 CLASS D

D

R .125

B

A

R .500

R

.422

90°

REQUIREMENTS:

1.

MATERIAL: CORRISION RESISTANT STEEL IN ACCORDNACE

WITH AMS 5510.

2.

DIMENSIONING AND TOLERANCING: DIMENSIONING AND

TOLERANCING SHALL BE IN ACCORDANCE WITH ANSI Y14

5M

3.

TOLERANCE: UNLESS OTHERWISE SPECIFIED, TOLERANCES

SHALL BE FOR LINEAR DIMENSION ±.015, ANGULAR ±2°.

4.

PART NUMBER: THE PART NUMBER SHALL CONSIST OF THE

BASIC MS NUMBER FOLLOWED BY A DASH NUMBER FROM

THE TABLE.

EXAMPLE:

MS9101 -02

DASH NUMBER

BASIC MS NUMBER

NOTES:

1.

ALL DIMENSIONS ARE IN INCHES.

2.

DO NOT USE UNASSIGNED PART NUMBERS.

3.

REMOVE BURRS AND BREAK SHARP EDGES.

AB

C

D

REF

REF

±.010

±.010

MS9101-01

0.500

0.500

0.328

0.328

MS9101-02

0.500

0.625

0.328

0.453

MS9101-03

0.500

0.750

0.328

0.578

MS9101-04

0.500

0.875

0.328

0.703

MS9101-05

0.500

1.000

0.328

0.828

MS9101-06

0.500

1.250

0.328

1.078

MS9101-07

0.500

1.500

0.328

1.328

MS9101-08

0.500

1.750

0.328

1.578

MS9101-10

0.625

0.625

0.453

0.453

MS9101-11

0.625

0.750

0.453

0.578

MS9101-12

0.625

0.875

0.453

0.703

MS9101-13

0.625

1.000

0.453

0.828

MS9101-14

0.625

1.250

0.453

1.078

MS9101-15

0.625

1.500

0.453

1.328

MS9101-16

0.625

1.750

0.453

1.578

MS9101-20

0.750

0.750

0.578

0.578

MS9101-21

0.750

0.875

0.578

0.703

MS9101-22

0.750

1.000

0.578

0.828

MS9101-23

0.750

1.250

0.578

1.078

MS9101-24

0.750

1.500

0.578

1.328

MS9101-25

0.750

1.750

0.578

1.578

MS9101-30

0.875

0.875

0.703

0.703

MS9101-31

0.875

1.000

0.703

0.828

MS9101-32

0.875

1.250

0.703

1.078

MS9101-33

0.875

1.500

0.703

1.328

MS9101-34

0.875

1.750

0.703

1.578

MS9101-40

1.000

1.000

0.828

0.828

MS9101-41

1.000

1.250

0.828

1.078

MS9101-42

1.000

1.500

0.828

1.328

MS9101-43

1.000

1.750

0.828

1.578

MS9101-44

1.000

2.000

0.828

1.828

DASH NO

C