Rev B

JFCW10 SERIES

10 Watt DC/DC Power Converters

10/31/2014

Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603-778-2300 • Toll Free: 888-597-9255 • Fax 603-778-9797

website: www.wallindustries.com • e-mail: sales@wallindustries.com

Page 1 of 5

Size:

1.00 x 1.00 x 0.39 inches

(25.4 x 25.4 x 9.9 mm)

Options:

•

Negative Logic Remote ON/OFF

•

Without Trim pin

•

Without CTRL Pin

•

Heatsink

FEATURES

•

High Efficiency up to 91%

•

Remote On/Off Control

•

4:1 Ultra Wide Input Voltage Ranges

•

Six-Sided Continuous Shielding

•

Ultra Low Quiescent Current

•

No Minimum Load Requirements

•

Single and Dual Outputs

•

Fixed Switching Frequency

•

Built-in EN55022 Class B Filter

•

10 Watts Maximum Output Power

•

Short Circuit, Over Voltage, Over Load, & Under-Voltage Protection

•

Wide Operating Temperature Range: -40°C to +85°C

•

Compliant to RoHS EU Directive 2011/65/EU

•

UL60950-1, EN60950-1, & IEC60950-1 Safety Approvals

•

CE Mark meets 2006/95/EC, 2011/95/EC, and 2004/108/EC

•

Optional Heatsink Available (Suffix “HC”)

DESCRIPTION

The JFCW10 series of DC/DC power converters provides 10 Watts of output power in an industry standard 1.00” x

1.00” x 0.39” package and footprint. This series has single and dual output models with 4:1 ultra wide input voltage

ranges of 9-36VDC and 18-75VDC. Some features include high efficiency up to 91%, 1600VDC I/O isolation, six-sided

shielding, and remote on/off control. These converters are also protected against short circuit, over voltage, over

load, and under-voltage. All models are RoHS compliant and have UL60950-1, EN60950-1, and IEC60950-1 safety

approvals. This series is best suited for use in wireless networks, telecom/datacom, industry control systems,

measurement equipment, and semiconductor equipment.

MODEL SELECTION TABLE

SINGLE OUTPUT MODELS

Model Number

Input Voltage Range

Output

Voltage

Output Current

Output

Ripple & Noise

No Load

Input Current

Output

Power

Efficiency

Maximum

Capacitive Load

Min Load

Max Load

JFCW24S33-10

24 VDC

(9 – 36 VDC)

3.3 VDC

0mA

3000mA

40mVp-p

6mA

9.9W

85%

3500µF

JFCW24S05-10

5 VDC

0mA

2000mA

40mVp-p

6mA

10W

87%

2500µF

JFCW24S12-10

12 VDC

0mA

830mA

60mVp-p

6mA

10W

90%

430µF

JFCW24S15-10

15 VDC

0mA

670mA

60mVp-p

6mA

10W

91%

350µF

JFCW24S24-10

24 VDC

0mA

416mA

60mVp-p

6mA

10W

90%

125µF

JFCW48S33-10

48 VDC

(18 – 75 VDC)

3.3 VDC

0mA

3000mA

40mVp-p

4mA

9.9W

85%

3500µF

JFCW48S05-10

5 VDC

0mA

2000mA

40mVp-p

4mA

10W

87%

2500µF

JFCW48S12-10

12 VDC

0mA

830mA

60mVp-p

4mA

10W

90%

430µF

JFCW48S15-10

15 VDC

0mA

670mA

60mVp-p

4mA

10W

90%

350µF

JFCW48S24-10

24 VDC

0mA

416mA

60mVp-p

4mA

10W

90%

125µF

DUAL OUTPUT MODELS

Model Number

Input Voltage Range

Output

Voltage

Output Current

Output

Ripple & Noise

No Load

Input Current

Output

Power

Efficiency

Maximum

Capacitive Load

Min Load

Max Load

JFCW24D05-10

24 VDC

(9 – 36 VDC)

±5 VDC

0mA

±1000mA

40mVp-p

6mA

10W

87%

±1440µF

JFCW24D12-10

±12 VDC

0mA

±416mA

60mVp-p

6mA

10W

89%

±250µF

JFCW24D15-10

±15 VDC

0mA

±333mA

60mVp-p

6mA

10W

89%

±180µF

JFCW48D05-10

48 VDC

(18 – 75 VDC)

±5 VDC

0mA

±1000mA

40mVp-p

4mA

10W

87%

±1440µF

JFCW48D12-10

±12 VDC

0mA

±416mA

60mVp-p

4mA

10W

89%

±250µF

JFCW48D15-10

±15 VDC

0mA

±333mA

60mVp-p

4mA

10W

89%

±180µF

NOTES

1. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor

between the Trim pin and either the +Vout pin or the –Vout pin.

2. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor suggested is Nippon chemi-con KY

series, 220µF/100V.

3. The JFCW10 series standard modules meet EN55022 Class A without external components and meets Class B with external components. See page 4 for more

details.

4. Both positive logic and negative logic remote on/off control is available. Positive logic remote on/off comes standard; for negative logic remote on/off add

the suffix “R” to the model number (Ex: JFCW24S05-10R).

5. There are several different options available for this series. Please see the “Model Number Setup” on page 5 for all options and ordering information.

6. Optional heatsink is available. Please call factory for more information.

CAUTION: This power module is not internally fused. An input line fuse must always be used.

*Due to advances in technology, specifications subject to change without notice.