OPA725, OPA2725

OPA726, OPA2726

SBOS278B − SEPTEMBER 2003 − REVISED JANUARY 2004

www.ti.com

2

ORDERING INFORMATION

PRODUCT

PACKAGE-LEAD

PACKAGE

DESIGNATOR(1)

SPECIFIED

TEMPERATURE

RANGE

PACKAGE

MARKING

ORDERING

NUMBER

TRANSPORT

MEDIA, QUANTITY

Non-Shutdown

OPA725

SOT23-5

DBV

−40

°C to +125°C

OALI

OPA725AIDBVT

Tape and Reel, 250

″

″

″

″

″

OPA725AIDBVR

Tape and Reel, 3000

OPA725

SO-8

D

−40

°C to +125°C

OPA725A

OPA725AID

Rails, 100

″

″

″

″

″

OPA725AIDR

Tape and Reel, 2500

OPA2725

SO-8

D

−40

°C to +125°C

OPA2725A

OPA2725AID

Rails, 100

″

″

″

″

″

OPA2725AIDR

Tape and Reel, 2500

OPA2725

MSOP-8

DGK

−40

°C to +125°C

BGM

OPA2725AIDGKT

Tape and Reel, 250

″

″

″

″

″

OPA2725AIDGKR

Tape and Reel, 2500

Shutdown

OPA726

SO-8

D

−40

°C to +125°C

OPA726A

OPA726AID

Rails, 100

″

″

″

″

″

OPA726AIDR

Tape and Reel, 2500

OPA726

MSOP-8

DGK

−40

°C to +125°C

BHC

OPA726AIDGKT

Tape and Reel, 250

″

″

″

″

″

OPA726AIDGKR

Tape and Reel, 2500

OPA2726

MSOP-10

DGS

−40

°C to +125°C

BHB

OPA2726AIDGST

Tape and Reel, 250

″

″

″

″

″

OPA2726AIDGSR

Tape and Reel, 2500

(1) For the most current package and ordering information, see the Package Option Addendum located at the end of this datasheet.

This integrated circuit can be damaged by ESD. Texas

Instruments recommends that all integrated circuits be

handled with appropriate precautions. Failure to observe

proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to

complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could

cause the device not to meet its published specifications.

Supply Voltage

+13.2V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Signal Input Terminals, Voltage(2)

−0.5V to (V+) + 0.5V

. . . . . . . . .

Current(2)

±10mA

. . . . . . . . . . . . . . . . . . .

Output Short Circuit(3)

Continuous

. . . . . . . . . . . . . . . . . . . . . . . . .

Operating Temperature

−55

°C to +125°C

. . . . . . . . . . . . . . . . . . . . .

Storage Termperature

−55

°C to +150°C

. . . . . . . . . . . . . . . . . . . . . .

Junction Temperature

+150

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead Temperature (soldering, 10s)

+300

°C

. . . . . . . . . . . . . . . . . . . .

ESD Rating (Human Body Model)

1000 V

. . . . . . . . . . . . . . . . . . . .

(1) Stresses above these ratings may cause permanent damage.

Exposure to absolute maximum conditions for extended periods

may degrade device reliability. These are stress ratings only, and

functional operation of the device at these or any other conditions

beyond those specified is not supported.

(2) Input terminals are diode-clamped to the power-supply rails.

Input signals that can swing more than 0.5V beyond the supply

rails should be current limited to 10mA or less.

(3) Short-circuit to ground, one amplifier per package.