Electronic Components Datasheet Search |
|
TPS40061PWPR Datasheet(PDF) 11 Page - Texas Instruments |
|
|
TPS40061PWPR Datasheet(HTML) 11 Page - Texas Instruments |
11 / 39 page R ILIM + I OC R DS(on)[max] I SINK ) V OS I SINK (W) ( ) ( ) O O LIM LOAD START C V I I A t é ù ´ = + ê ú ë û TPS40060 TPS40061 www.ti.com SLUS543F – DECEMBER 2002 – REVISED JUNE 2013 PROGRAMMING CURRENT LIMIT This device uses a two-tier approach for overcurrent protection. The first tier is a pulse-by-pulse protection scheme. Current limit is implemented on the high-side MOSFET by sensing the voltage drop across the MOSFET when the gate is driven low. The MOSFET voltage is compared to the voltage dropped across a resistor connected from VIN pin to the ILIM pin when driven by a constant current sink. If the voltage drop across the MOSFET exceeds the voltage drop across the ILIM resistor, the switching pulse is immediately terminated. The MOSFET remains off until the next switching cycle is initiated. The second tier consists of a fault counter. The fault counter is incremented on an overcurrent pulse and decremented on a clock cycle without an overcurrent pulse. When the counter reaches seven (7) a restart is issued and seven soft-start cycles are initiated. Both the upper and lower MOSFETs are turned off during this period. The counter is decremented on each soft-start cycle. When the counter is decremented to zero, the PWM is re-enabled. If the fault has been removed the output starts up normally. If the output is still present the counter counts seven overcurrent pulses and re-enters the second-tier fault mode. See Figure 7 for typical overcurrent protection waveforms. The minimum current limit setpoint (ILIM) depends on tSTART, CO, VO, and the load current at start-up (ILOAD). (6) The current limit programming resistor (RILIM) is calculated using Equation 7. Care must be taken in choosing the values used for VOS and ISINK in the equation. In order to ensure the output current at the overcurrent level, the minimum value of ISINK and the maximum value of VOS must be used. where: • ISINK is the current into the ILIM pin and is nominally 8.3 µA, minimum • IOC is the overcurrent setpoint which is the DC output current plus one-half of the peak inductor current • VOS is the overcurrent comparator offset and is 50 mV maximum (7) BP5, BP10 AND BPN10 INTERNAL VOLTAGE REGULATOR Start-up characteristics of the BP5, BP10 and BPN10 regulators are shown in Figure 7. Slight variations in the BP5 occurs dependent upon the switching frequency. Variation in the BPN10 and BP10 regulation characteristics is also based on the load presented by switching the external MOSFETs. Copyright © 2002–2013, Texas Instruments Incorporated Submit Documentation Feedback 11 Product Folder Links: TPS40060 TPS40061 |
Similar Part No. - TPS40061PWPR |
|
Similar Description - TPS40061PWPR |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |