Electronic Components Datasheet Search |
|
MF6CWM-100 Datasheet(PDF) 4 Page - National Semiconductor (TI) |
|
|
MF6CWM-100 Datasheet(HTML) 4 Page - National Semiconductor (TI) |
4 / 20 page Op Amp Electrical Characteristics (Continued) Boldface limits apply for T MIN to TMAX; all other limits TA = TJ = 25˚C. Parameter Conditions Typical Tested Design Units (Note 8) Limit Limit (Note 9) (Note 10) V + = +2.5V, V− = −2.5V Input Bias Current 10 pA CMRR (Op-Amp #2 Only) VCM1 = +0.5V, 60 55 dB VCM2 = −0.9V Output Voltage Swing RL = 10 kΩ +1.5 +1.3 +1.1 V −2.2 −1.7 −1.7 Maximum Output Short Source 24 mA Circuit Current (Note 6) Sink 1.0 Slew Rate 6.0 V/µs DC Open Loop Gain 67 dB Gain Bandwidth Product 1.2 MHz Logic Input-Output Electrical Characteristics (Note 5) The following specifications apply for V − = 0V unless otherwise specified. Boldface limits apply for T MIN to T MAX; all other limits TA = TJ = 25˚C. Parameter Conditions Typical Tested Design Units (Note 8) Limit Limit (Note 9) (Note 10) TTL CLOCK INPUT, CLK R PIN (Note 7) Maximum VIL, Logical “0” 0.8 0.8 V Input Voltage Minimum VIH, Logical “1” 2.0 2.0 V Input Voltage Maximum Leakage Current L Sh Pin at 2.0 2.0 µA at CLK R Pin Mid- Supply SCHMITT TRIGGER VT+, Positive Going Min V + = 10V 7.0 6.1 6.1 V Threshold Voltage Max 8.9 8.9 Min V + = 5V 3.5 3.1 3.1 V Max 4.4 4.4 VT−, Negative Going Min V + = 10V 3.0 1.3 1.3 V Threshold Voltage Max 3.8 3.8 Min V + = 5V 1.5 0.6 0.6 V Max 1.9 1.9 Hysteresis (VT+ −VT−) Min V + = 10V 4.0 2.3 2.3 V Max 7.6 7.6 Min V + = 5V 2.0 1.2 1.2 V Max 3.8 3.8 Minimum Logical “1” Output Io = −10µA V + = 10V 9.0 9.0 V Voltage (Pin 11) V + = 5V 4.5 4.5 Maximum Logical “0” Output Io = 10µA V + = 10V 1.0 1.0 V Voltage (Pin 11) V + = 5V 0.5 0.5 Minimum Output Source CLK R Tied V + = 10V 6.0 3.0 3.0 mA Current (Pin 11) to Ground V + = 5V 1.5 0.75 0.75 Maximum Output Sink CLK R Tied V + = 10V 5.0 2.5 2.5 mA Current (Pin 11) to V + V + = 5V 1.3 0.65 0.65 Note 1: The cutoff frequency of the filter is defined as the frequency where the magnitude response is 3.01 dB less than the DC gain of the filter. Note 2: For ±5V supplies the dynamic range is referenced to 2.82 Vrms (4V peak) where the wideband noise over a 20 kHz bandwidth is typically 200 µVrms for the MF6-50 and 250 µVrms for the MF6-100. For ±2.5V supplies the dynamic range is referenced to 1.06 Vrms (1.5V peak) where the wideband noise over a 20 kHz bandwidth is typically 140 µVrms for both the MF6-50 and the MF6-100. Note 3: The specifications for the MF6 have been given for a clock frequency (fCLK) of 250 kHz and less. Above this clock frequency the cutoff frequency begins to deviate from the specified error band of ±1.0% but the filter still maintains its magnitude characteristics. See Application Hints, Section 1.5. www.national.com 4 |
Similar Part No. - MF6CWM-100 |
|
Similar Description - MF6CWM-100 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |