Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

Surface Mount

PXE

Series

・Super low ESR, impedance and high heat resistance have been obtained by using

conductive polymer as electrolyte.

(ESR and rated ripple current values are improved from PXA series.)

・Suitable for DC-DC converters, voltage regulators and decoupling applications used on

computer motherboards etc.

・Solvent resistant type (see PRECAUTIONS AND GUIDELINES)

・RoHS Compliant

・Halogen Free

◆SPECIFICATIONS

Items

Characteristics

Category

Temperature Range

-55 to +105

℃

Rated Voltage Range

Capacitance Tolerance

±20% (M)

(at 20

℃, 120Hz)

Surge Voltage

Rated voltage

×1.15

(at 105

℃)

Leakage Current

Shall not exceed values shown in STANDARD RATINGS.

(at 20

℃ after 2 minutes)

Dissipation Factor

(tanδ)

0.12 max.

(at 20

℃, 120Hz)

Low Temperature

Characteristics

(Max. Impedance Ratio)

Z(-25

℃)/Z(+20℃)≦1.15

Z(-55

℃)/Z(+20℃)≦1.25

(at 100kHz)

Endurance

The following specifications shall be satisfied when the capacitors are restored to 20

℃ after the rated voltage is applied for 15,000 hours

at 105

℃.

Appearance

No significant damage

Capacitance change

≦±20% of the initial value

D.F. (tan

δ)

≦150% of the initial specified value

ESR

≦150% of the initial specified value

Leakage current

≦The initial specified value

Bias Humidity

The following specifications shall be satisfied when the capacitors are restored to 20

℃ after subjecting them to the DC rated voltage at

60

℃, 90 to 95% RH for 1,000 hours.

Appearance

No significant damage

Capacitance change

≦±20% of the initial value

D.F. (tan

δ)

≦150% of the initial specified value

ESR

≦150% of the initial specified value

Leakage current

≦The initial specified value

Surge Voltage

The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105

℃ for 30 seconds

through a protective resistor(R=1k

Ω) and discharge for 5 minutes 30 seconds.

Appearance

No significant damage

Capacitance change

≦±20% of the initial value

D.F. (tan

δ)

≦150% of the initial specified value

ESR

≦150% of the initial specified value

Leakage current

≦The initial specified value

Failure Rate

0.5% per 1,000 hours maximum (Confidence level 60% at 105

℃)

*Note : If any doubt arises, measure the leakage current after the following voltage treatment.

Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105

℃.

◆DIMENSIONS [mm]

L

±0.3 (Note)

0.3max.

A

±0.2

W

Size Code

E61

F61

F80

H70

H80

HA0

HC0

J80

JA0

JC0

φD

5

6.3

6.3

8

8

8

8

10

10

10

L

5.8

5.8

7.7

6.7

7.7

10.0

12.0

7.7

10.0

12.2

A

5.3

6.6

6.6

8.3

8.3

8.3

8.3

10.3

10.3

10.3

B

5.3

6.6

6.6

8.3

8.3

8.3

8.3

10.3

10.3

10.3

C

5.9

7.2

7.2

9.0

9.0

9.0

9.0

11.0

11.0

11.0

W

0.5 to 0.8

0.5 to 0.8

0.5 to 0.8

0.7 to 1.1

0.7 to 1.1

0.7 to 1.1

0.7 to 1.1

0.7 to 1.1

0.7 to 1.1

0.7 to 1.1

P

1.4

1.9

1.9

3.1

3.1

3.1

3.1

4.5

4.5

4.5

●

Terminal Code : A

◆PART NUMBERING SYSTEM

Supplement code

Size code

Capacitance tolerance code

Capacitance code (ex. 47µF:470,100µF:101)

Taping code

Terminal code

Voltage code (ex. 6.3V:6R3,10V:100)

Series code

Category

A P X E

A R A

G

M

1

3

4

2

6

7

8

9

10

13

12

5

18

17

16

11

15

14

Please refer to "Product code guide (conductive polymer type)"

Lower ESR

PXE

Lower ESR

PXA P42

PXF P38

◆MARKING

390

EX) 2.5V390

µF

40

CAT. No. E1001Q

CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS