OPA373, OPA2373

OPA374

OPA2374, OPA4374

SBOS279D − SEPTEMBER 2003 − REVISED DECEMBER 2004

www.ti.com

2

PRODUCT

PACKAGE-LEAD

PACKAGE

DESIGNATOR

SPECIFIED

TEMPERATURE

RANGE

PACKAGE

MARKING

ORDERING

NUMBER

TRANSPORT

MEDIA, QUANTITY

Shutdown

OPA373

SOT23-6

DBV

−40

°C to +125°C

A75

OPA373AIDBVT

Tape and Reel, 250

″

″

″

″

″

OPA373AIDBVR

Tape and Reel, 3000

OPA373

SO-8

D

−40

°C to +125°C

OPA373A

OPA373AID

Rails, 100

″

″

″

″

″

OPA373AIDR

Tape and Reel, 2500

OPA2373

MSOP-10

DGS

−40

°C to +125°C

AYO

OPA2373AIDGST

Tape and Reel, 250

″

″

″

″

″

OPA2373AIDGSR

Tape and Reel, 2500

Non-Shutdown

OPA374

SOT23-5

DBV

−40

°C to +125°C

A76

OPA374AIDBVT

Tape and Reel, 250

″

″

″

″

″

OPA374AIDBVR

Tape and Reel, 3000

OPA374

SO-8

D

−40

°C to +125°C

OPA274A

OPA374AID

Rails, 100

″

″

″

″

″

OPA374AIDR

Tape and Reel, 2500

OPA2374

SOT23-8

DCN

−40

°C to +125°C

ATP

OPA2374AIDCNT

Tape and Reel, 250

″

″

″

″

″

OPA2374AIDCNR

Tape and Reel, 3000

OPA2374

SO-8

D

−40

°C to +125°C

OPA2374A

OPA2374AID

Rails, 100

″

″

″

″

″

OPA2374AIDR

Tape and Reel, 2500

OPA4374

SO-14

D

−40

°C to +125°C

OPA4374A

OPA4374AID

Rails, 58

″

″

″

″

″

OPA4374AIDR

Tape and Reel, 2500

OPA4374

TSSOP-14

PW

−40

°C to +125°C

OPA4374A

OPA4374AIPWT

Tape and Reel, 250

″

″

″

″

″

OPA4374AIPWR

Tape and Reel, 2500

(1) For the most current package and ordering information, see the Package Option Addendum located at the end of this datasheet.

Supply Voltage

+7.0V

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Signal Input Terminals, Voltage(2)

−0.5V to (V+) + 0.5V

. . . . . . . . .

Current(2)

±10mA

. . . . . . . . . . . . . . . . . . .

Output Short-Circuit(3)

Continuous

. . . . . . . . . . . . . . . . . . . . . . . . .

Operating Temperature

−55

°C to +150°C

. . . . . . . . . . . . . . . . . . . . .

Storage Temperature

−65

°C to +150°C

. . . . . . . . . . . . . . . . . . . . . . .

Junction Temperature

+150

°C

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Lead Temperature (soldering, 10s)

+300

°C

. . . . . . . . . . . . . . . . . . . .

(1) Stresses above these ratings may cause permanent damage.

Exposure to absolute maximum conditions for extended periods

may degrade device reliability. These are stress ratings only, and

functional operation of the device at these or any other conditions

beyond those specified is not implied.

(2) Input terminals are diode-clamped to the power-supply rails.

Input signals that can swing more than 0.5V beyond the supply

rails should be current-limited to 10mA or less.

(3) Short-circuit to ground, one amplifier per package.

This integrated circuit can be damaged by ESD. Texas

Instruments recommends that all integrated circuits be

handled with appropriate precautions. Failure to observe

proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to

complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could

cause the device not to meet its published specifications.