Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

2-21002-1 Datasheet(PDF) 2 Page - TE Connectivity Ltd

Part # 2-21002-1
Description  Seating Tool Assembly
Download  3 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TEC [TE Connectivity Ltd]
Direct Link  http://www.te.com/usa-en/home.html
Logo TEC - TE Connectivity Ltd

2-21002-1 Datasheet(HTML) 2 Page - TE Connectivity Ltd

  2-21002-1 Datasheet HTML 1Page - TE Connectivity Ltd 2-21002-1 Datasheet HTML 2Page - TE Connectivity Ltd 2-21002-1 Datasheet HTML 3Page - TE Connectivity Ltd  
Zoom Inzoom in Zoom Outzoom out
 2 / 3 page
background image
408-8996
2 of 3
Rev A
For available application tools, call PRODUCT INFO
at the number at the bottom of page 1.
CAUTION
!
Over-driving of the connector assembly will deform
parts critical to the quality of the connection.
Maximum force occurs prior to the connector
assembly bottoming on the pc board.
4. SETUP
When setting up equipment to seat the connector
assembly, pay particular attention to the alignment of
the seating tool, connector assembly, and application
tool ram before cycling the application tool.
CAUTION
!
If the seating tool and connector assembly are
improperly aligned, damage could occur to the
tooling, connector assembly, or both.
1. Set tool seating height to the dimension shown in
Figure 2 (application tool shut height will equal the
tool seating height PLUS the combined thicknesses
of the pc board and support fixture). After seating, a
gap of no more than 0.10 mm [.004 in.] between the
connector assembly standoffs and the pc board
is allowed.
NOTE
i
Use the tool seating height as a reference starting
point. This height may need to be adjusted to
obtain the amount allowed (maximum of 0.10 mm
[.004 in.]) between the standoffs of the connector
assembly and the pc board.
5. SEATING (Figure 2)
1. Place the pc board on the support fixture.
2. Orient the seating tool over the connector
assembly so that the back plate is aligned with the
back of the connector assembly and the cutout is
aligned with the PoE chip set. Then lower the
seating tool until it bottoms on the connector
assembly.
3. Place the connector assembly on the pc board so
that the contacts and alignment posts are aligned
and started into the matching holes in the pc board.
4. Center the seating tool (with the connector
assembly) under the ram of the application tool.
Slowly lower the ram until it just meets the seating
tool. Verify alignment of pc board support, pc board,
connector assembly, and seating tool.
CAUTION
!
Damage to the pc board, seating tool, or connector
assembly may occur if the seating tool is not
properly seated on the connector assembly before
cycling the application tool.
5. Cycle the application tool to seat the connector
assembly on the pc board. Then retract the ram,
and carefully remove the seating tool by pulling it
straight from the connector assembly.
DIMENSION A
Tool Seating Height
(With Connector Assembly Seated)
DIMENSION B
Maximum Gap Allowed
37.92 mm [1.493 in.]
0.10 mm [.004 in.]
Ram of Applicator Tool
(Fully Down)
Seating Tool
Note: Not to Scale
Application Tool
Shut Height
(Ram Fully Down)
(See Section 4, Step 1)
Connector Assembly
Contacts and Alignment
Posts Inserted into Holes
in PC Board and PC
Board Support Fixture
PC Board
PC Board
Support Fixture
A
B
Figure 2


Similar Part No. - 2-21002-1

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
2-21002-1 TEC-2-21002-1 Datasheet
106Kb / 4P
   Reasons for reissue are provided in Section 7, REVISION SUMMARY.
More results

Similar Description - 2-21002-1

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
408-32200 TEC-408-32200 Datasheet
405Kb / 3P
   CFP2 and CFP4 Cage Assembly Seating Tool
logo
Tyco Electronics
408-8503 MACOM-408-8503 Datasheet
122Kb / 3P
   Seating Tool Assemblies
logo
TE Connectivity Ltd
408-32199 TEC-408-32199 Datasheet
402Kb / 3P
   CFP2 and CFP4 Cage Assembly Seating Tool
408-32212 TEC-408-32212 Datasheet
333Kb / 4P
   Small Form-Factor Pluggable Cage Assembly Seating Tool
logo
Tyco Electronics
408-4109 MACOM-408-4109 Datasheet
547Kb / 5P
   Pistol Grip Seating Tool
logo
TE Connectivity Ltd
408-10380 TEC-408-10380 Datasheet
69Kb / 3P
   CXP Seating Tool Kit
logo
Molex Electronics Ltd.
0638120500 MOLEX11-0638120500 Datasheet
35Kb / 1P
   Manual Insertion Tool, Star Ring Seating Tool
0638120500 MOLEX-0638120500 Datasheet
31Kb / 1P
   Manual Insertion Tool, Star Ring Seating Tool
08/03/2021
logo
TE Connectivity Ltd
408-32028 TEC-408-32028 Datasheet
84Kb / 4P
   Mini-SAS HD Seating Tool Kit
408-9623 TEC-408-9623 Datasheet
96Kb / 3P
   Seating Tool 535072- 1 for Type C
More results


Html Pages

1 2 3


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com