 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
408-32028 Datasheet(PDF) 2 Page - TE Connectivity Ltd |
|
||||||||||||||||||||||||||||||
408-32028 Datasheet(HTML) 2 Page - TE Connectivity Ltd |
|
|
2 / 4 page  CAUTION ! 408-32028 2 of 4 Rev A Over-driving of the connector and cage assembly will deform parts critical to the quality of the connection. Maximum force occurs prior to the connector and cage assembly bottoming on the pc board. 4. SETUP When setting up equipment to seat the connector and cage assembly, pay particular attention to the following: • The seating tool must be matched to the connector and cage assembly. CAUTION ! If the seating tool and connector and cage assembly are mismatched or are improperly aligned, damage could occur to the tooling, connector and cage assembly, or both. • The wall support must be properly installed, and the seating tool, connector and cage assembly, and application tool ram must be properly aligned before cycling the application tool 1. Set tool seating height to the dimension shown in Figure 2 (application tool shut height will equal the tool seating height PLUS the combined thicknesses of the pc board and support fixture). After seating, a gap of no more than 0.10 mm [.004 in.] between the cage assembly standoffs and the pc board is allowed. NOTE i Use the tool seating height as a reference starting point. This height may need to be adjusted to obtain the amount allowed (maximum of 0.10 mm [.004 in.]) between the standoffs of the cage assembly and the pc board. 2. Slide the wall support into the port(s) of the cage assembly until the wall support is secure. 5. SEATING (see Figure 2) 1. Place the pc board on the support fixture. 2. Orient the seating tool over the cage assembly so that the back is aligned with the back of the cage assembly. Then lower the seating tool onto the cage assembly, making sure that the cutouts slide over the protruding components of the cage assembly, until the seating tool bottoms on the top of the cage assembly. 3. Place the connector and cage assembly on the pc board so that the contacts are aligned and started into the matching holes in the pc board. 4. Center the seating tool (with the connector and cage assembly) under the ram of the application tool. Slowly lower the ram until it just meets the seating tool. Verify alignment of pc board support,pc board, connector and cage assembly, and seating tool. Ram of Application Tool (Fully Down) Seating Tool 2018875-1 Cage Assembly Wall Support (Installed in Ports of Cage Assembly) Printed Circuit (PC) Board Press-Fit Contacts Inserted into Holes in PC Board Suport Fixture PC Board Support Fixture Application Tool Shut Height (Ram Fully Down) 0.1 mm (Max) Gap Allowed Figure 2 |
Similar Part No. - 408-32028 |
|
Similar Description - 408-32028 |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
