Electronic Components Datasheet Search |
|
2-21000-7 Datasheet(PDF) 2 Page - Tyco Electronics |
|
2-21000-7 Datasheet(HTML) 2 Page - Tyco Electronics |
2 / 4 page 408-8022 Conversion Kits 690675-2 and 692613-1 Rev A 2 of 4 Tyco Electronics Corporation 1. INTRODUCTION These conversion kits are used to modify AMP–O–LECTRIC Model K Terminating Machines to accept miniature quick–change applicators. Kit No. 690675–2 is required for all end–feed and those side–feed applicators that receive the strip terminals in a horizontal position. Refer to the exploded view and parts list in Figure 1 to make sure you have all the parts required for the conversion. Kit No. 690675–2 plus Kit No. 692613–1 are required for those side–feed applicators that receive the strip terminals in a vertical position. Throughout these instructions, where reference is madeto hand-cycling themachineand to the basic machine parts and assemblies, refer to Customer Manual 409-5128. Read the following instructions carefully before and during the installation of the conversion kits on the machine. 2. INSTALLATION OF CONVERSION KITS Before starting installation of the conversion kits, remove and store mechanical feed arm or air feed operation arm from feed mechanism shaft by loosening or removing clamp screws. During installation of the conversion kit, certain parts and assemblies MUST be removed and either placed in storage or retained for installation of the kit. This kit is not recommended for Models C, J, and J/K machines. MAKE CERTAIN that electrical power to the machineis OFF by pulling theplug from the receptacle. 2.1. Kit No. 690675-2 Installation (Figure 2) For installation of this kit, the machine must be equipped with the proper vertical reel bracket assembly (Part No. 694925–1). For information pertaining to this assembly, refer to Customer Manual 409–5128. 1. The left–hand stock guide is required ONLY when using side–feed applicators. With guide installed on the bracket, attach the bracket to the vertical reel bracket assembly with two screws capped with knurled knobs, as shown. 2. To guide the terminal strip properly into end–feed applicators, it is necessary that the right–hand stock guide bracket be lowered by using the UPPER hold in the vertical support for the left screw, as shown. 3. Remove the two base mount screws and washers form frame and install the base mount supplied in the kit. Adjust height of the base mount as low as possible in accordance with the machine manual. 4. Hand–cycle in accordance with the machine manual until the toggle link is at its lowest position. 5. Remove the arm retaining plate by removing the four screws. 6. Loosen the setscrew in the ram, and then pivot the toggle link toward the front of the machine and slide out the toggle link pin to remove the ram. 7. Lubricate the four sides of the new ram, supplied in the kit, as specified in the machine manual. 8. Pivot the toggle link forward and install the new ram with the toggle link pin removed in Step 6. Pivot the ram back into position and tighten the setscrew provided in the kit. 9. Install the ram retaining plate with the four screws removed in Step 6. 10. Hand–cycle the machine to the rest position (top dead center). 11. All parts removed for conversion, and any unused parts of the kit, should be retained and stored. 2.2. Kit No. 692613-1 Installation (Figure 3) This kit, in addition to Kit 690675–2, is required ONLY for side feed applicators that receive strip terminals in a vertical position. 1. Lay out the machine frame for holes as shown in Figure 3. 2. Drill two size “G” holes, and thread with 5/16–18 UNC–2B tap. 3. Assemble the reel support as shown and install on the machine with the two screws supplied in the kit. 3. INSTALLATION OF THE APPLICATOR FEED CAM it is NECESSARY for all miniature quick–change applicators, when used in an AMP–O–LECTRIC machine, to be equipped with the CORRECT feed cam as listed on the applicator parts list (log) supplied with the applicator. CHECK the feed cam, and if necessary, replace it as described in the applicator instructions supplied with the applicator. Retain all parts that are removed. NOTE i NOTE i CAUTION ! |
Similar Part No. - 2-21000-7 |
|
Similar Description - 2-21000-7 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |