Electronic Components Datasheet Search
Selected language     English  ▼
Part Name
         Description


5--21012--4 Datasheet(PDF) 3 Page - Tyco Electronics

Part No. 5--21012--4
Description  0.8mm CHAMP* Crimper Assemblies
Download  4 Pages
Scroll/Zoom Zoom In 100% Zoom Out
Maker  MACOM [Tyco Electronics]
Homepage  http://www.macom.com
Logo 

   
 3 page
background image
408- 4040
0.8mm CHAMP Crimper Assemblies 122842- 1, 122842- 2, and 122842- 3
3
of 4
Rev C
Tyco Electronics Corporation
3. Secure the cable in the cable clamp spring.
4. Slide the lower tooling assembly back against
the rear tool stop of the arbor frame assembly.
5. To crimp the metal backshell onto the cable,
lower the ram using the handle until the adjustment
ring is flush with the top of the arbor frame
assembly.
6. After the connector is crimped, use the handle
to raise the ram; then slide the lower tooling
assembly out from under the ram. Remove the
connector.
6. MAINTENANCE AND INSPECTION
It is recommended that a maintenance and inspection
program be performed periodically to ensure
dependable and uniform terminations. Frequency of
inspection depends on:
1. The care, amount of use, and handling of the
crimper assembly.
2. The presence of abnormal amounts of dust and
dirt.
3. The degree of operator skill.
4. Your own established standards.
The crimper assembly is inspected before being
shipped; however, it is recommended that the
assembly be inspected immediately upon its arrival at
your facility to ensure that it has not been damaged
during shipment. Due to the precision design, it is
important that no parts of the crimper assembly be
interchanged except the replacement parts listed in
Figure 3.
6.1. Daily Maintenance
1. Remove dust, moisture, and other contaminants
with a clean brush, or a soft, lint--free cloth. DO
NOT use objects that could damage the crimper
assembly.
2. Make certain that upper and lower
subassemblies and cable clamp springs are in
place and properly secured.
3. When the assembly is not in use, store it in a
clean, dry area.
6.2. Periodic Inspection
1. Remove all lubrication and accumulated film
with a suitable commercial degreaser that will not
affect paint or plastic material.
2. Make certain that all assembly components are
in place. If replacements are necessary, refer to
Section 7, REPLACEMENT AND REPAIR.
3. Inspect crimper assembly for worn, cracked,
chipped, or broken areas. If damage is evident,
return the assembly for evaluation and repair. See
Section 7, REPLACEMENT AND REPAIR.
7. REPLACEMENT AND REPAIR
Customer--replaceable parts are listed in Figure 3.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed
should be replaced by Tyco Electronics to ensure
quality and reliability. Order replacement parts
through your representative, or call 1--800--526--5142,
or send a facsimile of your purchase order to
717--986--7605, or write to:
CUSTOMER SERVICE (038--035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105--3608
For customer repair service, call 1--800--526--5136.
8. REVISION SUMMARY
Revisions to this instruction sheet include:
S
Updated instruction sheet to corporate
requirements




Html Pages

1  2  3  4 


Datasheet Download




Link URL

Does ALLDATASHEET help your business so far?  [ DONATE ]  

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Bookmark   |   Link Exchange   |   Manufacturer List
All Rights Reserved© Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  , Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp  |   Russian : Alldatasheetru.com
Korean : Alldatasheet.co.kr   |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com  |   Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl