Electronic Components Datasheet Search
  English  ▼
ALLDATASHEET.COM

X  

3-455888-7 Datasheet(PDF) 4 Page - TE Connectivity Ltd

Part # 3-455888-7
Description  Ocean side-feed applicators are available with either a mechanical feed, air feed, or servo feed system
Download  18 Pages
Scroll/Zoom Zoom In 100%  Zoom Out
Manufacturer  TEC [TE Connectivity Ltd]
Direct Link  http://www.te.com/usa-en/home.html
Logo TEC - TE Connectivity Ltd

3-455888-7 Datasheet(HTML) 4 Page - TE Connectivity Ltd

  3-455888-7 Datasheet HTML 1Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 2Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 3Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 4Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 5Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 6Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 7Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 8Page - TE Connectivity Ltd 3-455888-7 Datasheet HTML 9Page - TE Connectivity Ltd Next Button
Zoom Inzoom in Zoom Outzoom out
 4 / 18 page
background image
408-10390
Rev M1
4 of 18
2.1. Applicator with Mechanical Feed System
With this applicator, the terminals are fed by the action of the feed cam and a series of rods and levers, which
move the feed pawl. Two feed cams are available and can be mounted in two different mounting holes
depending on machine stroke length and feed type (see Figure 5). The spare feed cam, when not in use, can
be mounted to the applicator housing in the spare feed cam storage location shown in Figure 6.
NOTE
Pacific applicators can only be used with 30-mm stroke machines and, therefore, only have the 30-mm feed cam mounting
positions on the applicator ram.
The post-feed feed cam advances the lead terminal over the anvil on the downward stroke of the ram
assembly. The post-feed set up is typically used for leadmaker and end-feed bench applications.
The pre-feed feed cam advances the lead terminal over the anvil on the upward stroke of the ram assembly so
that a terminal is over the anvil when the machine is at rest. The pre-feed set up is typically used for side-feed
bench applications.
NOTE
The recommended setup for end-feed applications is post-feed. The applicator can be configured for pre-feed, but may
encounter problems with some applications. Feed issues or terminal jamming may occur in the pre-feed configuration.
2.2. Applicator with Air Feed System
With this applicator, the mechanical feed system feed cam and its mechanical system of rods, levers, and
springs are replaced by an air cylinder module. In the air feed module, the feed action is started when the
applicator ram moves. At the beginning of the ram’s downward stroke, the ram-mounted cam pushes the push
rod. This actuates the valve inside the air feed housing causing the retract side of the cylinder (closest to the
anvil) to be filled, shifting the feed pawl to the rear of the strip guide.
NOTE
The air supply connection (shown in Figure 2) must be connected to an air supply line providing continuous pressure of 5.00 to
6.00 bars [72 to 87 psi] at the applicator.
Figure 5
Mounting Feed Cam
40-mm [15/8-in.] Stroke Machine
30-mm [11/8-in.] Stroke Machine
Mounting Screw
Post-Feed
Pre-Feed
Post-Feed
Pre-Feed Feed Cam
Post-Feed Feed Cam
Feed Cam
Installed
Pre-Feed
Mounting Screw
Feed Cam
Installed
Counter
Magnet


Similar Part No. - 3-455888-7

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
3-455888-7 TEC-3-455888-7 Datasheet
5Mb / 4P
   THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION
3-455888-7 TEC-3-455888-7 Datasheet
880Kb / 19P
   Ocean Side-Feed Applicators
3-455888-7 TEC-3-455888-7 Datasheet
5Mb / 4P
   SHOULD BE CONTACTED FOR THE LATEST REVISION.
More results

Similar Description - 3-455888-7

ManufacturerPart #DatasheetDescription
logo
TE Connectivity Ltd
408-10389 TEC-408-10389 Datasheet
880Kb / 19P
   Ocean Side-Feed Applicators
logo
Molex Electronics Ltd.
0638013501 MOLEX11-0638013501 Datasheet
33Kb / 1P
   Applicator Air Feed Assembly
638812000 MOLEX-638812000 Datasheet
211Kb / 7P
   Mechanical Feed Metal Strip Applicator
09-30-05
638325100 MOLEX-638325100 Datasheet
166Kb / 5P
   Mechanical Feed-Front Metal Strip
01-19-06
63881-0800 MOLEX-63881-0800 Datasheet
479Kb / 7P
   Mechanical Feed Metal Strip Applicator
05-16-12
63881-5700 MOLEX-63881-5700 Datasheet
279Kb / 7P
   Mechanical Feed Metal Strip Applicator
04-13-09
638810100 MOLEX-638810100 Datasheet
197Kb / 6P
   Mechanical Feed Metal Strip Applicator
09-30-05
638812200 MOLEX-638812200 Datasheet
195Kb / 6P
   Mechanical Feed Metal Strip Applicator
09-30-05
638325200 MOLEX-638325200 Datasheet
303Kb / 5P
   Mechanical Feed Metal Strip Applicator
07-24-17
638810200 MOLEX-638810200 Datasheet
210Kb / 7P
   Mechanical Feed Metal Strip Applicator
09-30-05
More results


Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18


Datasheet Download

Go To PDF Page


Link URL




Privacy Policy
ALLDATASHEET.COM
Does ALLDATASHEET help your business so far?  [ DONATE ] 

About Alldatasheet   |   Advertisement   |   Datasheet Upload   |   Contact us   |   Privacy Policy   |   Link Exchange   |   Manufacturer List
All Rights Reserved©Alldatasheet.com


Mirror Sites
English : Alldatasheet.com  |   English : Alldatasheet.net  |   Chinese : Alldatasheetcn.com  |   German : Alldatasheetde.com  |   Japanese : Alldatasheet.jp
Russian : Alldatasheetru.com  |   Korean : Alldatasheet.co.kr  |   Spanish : Alldatasheet.es  |   French : Alldatasheet.fr  |   Italian : Alldatasheetit.com
Portuguese : Alldatasheetpt.com  |   Polish : Alldatasheet.pl  |   Vietnamese : Alldatasheet.vn
Indian : Alldatasheet.in  |   Mexican : Alldatasheet.com.mx  |   British : Alldatasheet.co.uk  |   New Zealand : Alldatasheet.co.nz
Family Site : ic2ic.com  |   icmetro.com