Electronic Components Datasheet Search |
|
91912-2 Datasheet(PDF) 3 Page - TE Connectivity Ltd |
|
91912-2 Datasheet(HTML) 3 Page - TE Connectivity Ltd |
3 / 4 page 408-8582 3 of 4 Rev A 6. Allow the tool handles to open fully and remove the crimped connector from the dies. 5. CRIMP HEIGHT ADJUSTMENT The tool frame assembly ratchet mechanism features an adjustment wheel with numbered settings. If the crimp height is not acceptable, adjust the ratchet as follows: 1. Remove the lockscrew from the ratchet adjustment wheel. 2. With a screwdriver, adjust the ratchet wheel from the opposite side of the tool. 3. Observe the ratchet adjustment wheel. If a tighter crimp is required, rotate the adjustment wheel COUNTERCLOCKWISE to a higher-numbered setting. If a looser crimp is required, rotate the adjustment wheel CLOCKWISE to a lower- numbered setting. 4. Replace the lockscrew. 5. Make a sample crimp and measure the crimp height. If the crimp height is acceptable, secure the lockscrew. If the dimension is unacceptable, remove lockscrew and continue to adjust the ratchet, and again measure a sample crimp. 6. MAINTENANCE AND INSPECTION 6.1. Maintenance 1. Remove dust, moisture, and other contaminants with a clean, soft brush, or a clean, soft, lint-free cloth. Do NOT use any objects that could damage the dies or tool. 2. Make sure that the proper die-retaining screws are properly secured. 3. When the dies are not in use, store them in a clean, dry area. 4. Store the tool with the tool handles closed to prevent objects from becoming lodged within the jaws. 6.2. Inspection 1. Remove all lubrication and accumulated film from the dies by immersing the dies in a suitable commercial degreaser. 2. Make certain that all die-retaining screws and die components are properly secured. 3. Inspect the crimping surfaces for flattened, chipped, worn, or cracked areas. If damage is evident, the dies must be replaced. Refer to Section 7, REPLACEMENT. Screwdriver Lockscrew (Typ) Ratchet Adjustment Wheel Figure 4 6.3. Measuring the Die Opening The die assembly will perform correctly as long as: (1) the product specified is correct for the application, (2) the specific die assembly is used, (3) the die assembly has been measured to ensure that the openings are correct, and (4) the tool has been adjusted correctly. Figure 5 provides information on die opening sizes. 7. REPLACEMENT These crimping die assemblies are inspected before shipment. It is recommended that the dies be inspected immediately upon arrival at your facility to ensure that the dies have not been damaged during shipment. Order replacements through your local TE representative, or call 1-800-526-5142, or send a facsimile of your purchase order to 1-717-986-7605, or write to: CUSTOMER SERVICE (038-035) TYCO ELECTRONICS CORPORATION PO BOX 3608 HARRISBURG PA 17105-3608 8. REVISION SUMMARY Revisions to this instruction sheet include: • Changed company name and logo |
Similar Part No. - 91912-2 |
|
Similar Description - 91912-2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |