Electronic Components Datasheet Search |
|
1752938-2 Datasheet(PDF) 1 Page - Tyco Electronics |
|
1752938-2 Datasheet(HTML) 1 Page - Tyco Electronics |
1 / 5 page Instruction Sheet SDE- SA Hand Tool Assembly 1752938- 1 408--10002 LOC B 1 of 5 E 2010 Tyco Electronics Corporation, Berwyn, PA All Rights Reserved TE logo and Tyco Electronics are trademarks. *Trademark. Other product names, logos, or company names might be trademarks of their respective owners. TOOLING ASSISTANCE CENTER 1--800--722--1111 PRODUCT INFORMATION 1--800--522--6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.tycoelectronics.com 06 APR 10 Rev C with Die Assembly 1752938- 2 PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended--use, production operations is available. Handle Emergency Ratchet Release Retaining Pins (4) Required Die Retention Screws Ratchet Adjustment Wheel Moving Jaw Anvil (Lower) Insulation Die Die Set 1752938--2 Nut Locator Insulation Crimper (Upper Die) Stationary Jaw Anvil (Lower) Wire Die Wire Crimper (Upper Die) Die Assembly Contact Wire Die Assembly Part Number Contact Size Insulation Dia (Max) Strip Length 1752938 2 925660--1 (Pin) 0.75--1.0 [.030--.039] 4 5 [ 177] 4 5 +0 5 [ 177 + 020] 1752938--2 925661--1 (Skt) 1.38--1.64 [.054--.065] 4.5 [.177] 4.5 +0.5 [.177 +.020] Figure 1 1. INTRODUCTION SDE--SA Hand Tool Assembly 1752938--1 consists of SDE--SA Frame Assembly 9--1478240--0 and die set assembly 1752938--2. See Figure 1. The tool is used to crimp 3.56 mm [.140 in.] diameter MATE--N--LOK* Pin and Socket Contacts. Dimensions in this instruction sheet are in millimeters [with inches in brackets]. Figures and illustrations are for reference only and are not drawn to scale. Reason for revision is given in Section 10, REVISION SUMMARY. 2. DESCRIPTION The tool frame features two jaws, a handle, ratchet adjustment wheel, and an emergency ratchet release. The die set consists of an indenter (upper die) and an anvil (lower die). The tool frame holds a die assembly with two crimping chambers. See Figure 1. Die retaining pins and die retaining screws are used to position and secure the dies in the tool frame. The tool features a ratchet and an adjustment wheel with a range of settings. The ratchet ensures that the tool has completed the cycle and will not release until the handles have been FULLY closed, unless the emergency ratchet release is rotated to manually release the ratchet. The adjustment wheel controls the amount of handle pressure exerted on the dies during the crimping procedure. The dies bottom before the ratchet releases. This feature ensures maximum tensile performance of the crimp. DO NOT re--adjust the ratchet. 3. INSTALLATION AND REMOVAL OF DIE SET AND LOCATOR ASSEMBLY (Figure 1) 1. Open the tool handles and remove the two die retaining screws from the tool jaws. NOTE i CAUTION ! |
Similar Part No. - 1752938-2 |
|
Similar Description - 1752938-2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |