Electronic Components Datasheet Search |
|
1-306105-1 Datasheet(PDF) 1 Page - TE Connectivity Ltd |
|
1-306105-1 Datasheet(HTML) 1 Page - TE Connectivity Ltd |
1 / 4 page Stationary Die Die Holding Screws Moving Die Locator / Insulation Stop Wire Range Marking ©2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company All Rights Reserved *Trademark TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 1 of 4 Instruction Sheet TOOLING ASSISTANCE CENTER 1-800-722-1111 PRODUCT INFORMATION 1-800-522-6752 This controlled document is subject to change. For latest revision and Regional Customer Service, visit our website at www.te.com LOC B 408-9442 Interchangeable Crimping Dies 58373-1 and 58374-1 (Used in Hand Crimping Tool 69710-1 and Pneumatic Tools 69365, 69365-2, and 69365-3) 06 DEC 11 Rev B PROPER USE GUIDELINES Cumulative Trauma Disorders can result from the prolonged use of manually powered hand tools. Hand tools are intended for occasional use and low volume applications. A wide selection of powered application equipment for extended-use, production operations is available. Figure 1 1. INTRODUCTION Interchangeable Crimping Die Assemblies 58373-1 and 58374-1 (see Figure 1) are designed to be used in Hand Crimping Tool 69710-1 and Pneumatic Tools 69365, 69365-2, and 69365-3 to crimp .140 MATE-N- LOK* loose piece pin and socket contacts listed in Figure 2. Die set 58373-1 crimps No. 10 AWG wires and die set 58374-1 crimps 14-12 AWG wires. Read these instructions thoroughly before starting. NOTE i Measurements are in millimeters [followed by inch equivalents in brackets]. Figures and illustrations are for identification only and are not drawn to scale. Reasons for reissue are provided in Section 7, REVISION SUMMARY. 2. DESCRIPTION Each crimping die assembly consists of a moving die and a stationary die, as shown in Figure 1. The moving die is positioned in the lower portion of the tool head and is attached to the moving die holder by a die holding screw. The stationary die is secured to the stationary die holder located in the upper portion of the tool head. 3. DIE INSTALLATION If using the hand tool, follow the die installation steps in Paragraph 3.1; if using any of the pneumatic tools, follow the die installation steps in Paragraph 3.2. 3.1. Hand Tool 1. Position stationary die in stationary die holder and moving die in moving die holder. See Figure 3. Fasten die holding screws enough to hold dies in place but do NOT tighten fully. 2. Close handles until the dies bottom. Then tighten both holding screws. The tool can now be used to crimp the contacts to wires. NOTE i Check die alignment and tighten die holding screws. Pin Socket Wire Barrel Insulation Barrel Stabilizer Locator Slot Wire Strip NOTE: Not to Scale Length† †If insulation diameter range is 2.54-3.78 [.100-.149], wire strip length is 6.35 [.250]; if insulation diameter range is 3.81-4.06 [.150 to .160], wire strip length is 7.92 [.312]. CRIMPING DIE PART NUMBER WIRE SIZE (AWG) INSUL DIA RANGE† CRIMP SECT WIRE SIZE MARKING CONTACT PART NUMBER STRIP LOOSE PIECE 58374-1 14-12 2.54-4.06 [.100-.160] 14-12 350200 350201 350390 350391 58373-1 10 10 Figure 2 |
Similar Part No. - 1-306105-1 |
|
Similar Description - 1-306105-1 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |