 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
72V261LA20TFGI8 Datasheet(PDF) 3 Page - Integrated Device Technology |
|
||||||||||||||||||||||||||||||
72V261LA20TFGI8 Datasheet(HTML) 3 Page - Integrated Device Technology |
|
|
3 / 27 page  IDT72V261LA/72V271LA 3.3 VOLT CMOS SuperSync FIFO™ 16,384 x 9 and 32,768 x 9 3 COMMERCIAL AND INDUSTRIAL TEMPERATURE RANGES DESCRIPTION (CONTINUED) Figure 1. Block Diagram of Single 16,384 x 9 and 32,768 x 9 Synchronous FIFO DATA OUT (Q0 - Qn) DATA IN (D0 - Dn) MASTER RESET (MRS) READ CLOCK (RCLK) READ ENABLE (REN) OUTPUT ENABLE (OE) EMPTY FLAG/OUTPUT READY (EF/OR) PROGRAMMABLE ALMOST-EMPTY (PAE) WRITE CLOCK (WCLK) WRITE ENABLE (WEN) LOAD (LD) FULL FLAG/INPUT READY (FF/IR) PROGRAMMABLE ALMOST-FULL (PAF) IDT 72V261LA 72V271LA PARTIAL RESET (PRS) FIRST WORD FALL THROUGH/SERIAL INPUT (FWFT/SI) RETRANSMIT (RT) 4673 drw 03 HALF FULL FLAG (HF) SERIAL ENABLE(SEN) There are two possible timing modes of operation with these devices: IDT Standard mode and First Word Fall Through (FWFT) mode. In IDT Standard mode, the first word written to an empty FIFO will not appear on the data output lines unless a specific read operation is performed. A read operation, which consists of activating REN and enabling a rising RCLK edge, will shift the word from internal memory to the data output lines. In FWFT mode, the first word written to an empty FIFO is clocked directly to the data output lines after three transitions of the RCLK signal. A REN does not have to be asserted for accessing the first word. However, subsequent words written to the FIFO do require a LOW on REN for access. The state of the FWFT/SI input during Master Reset determines the timing mode in use. For applications requiring more data storage capacity than a single FIFO can provide, the FWFT timing mode permits depth expansion by chaining FIFOs in series (i.e. the data outputs of one FIFO are connected to the corresponding data inputs of the next). No external logic is re- quired. These FIFOs have five flag pins, EF/OR (Empty Flag or Output Ready), FF /IR (Full Flag or Input Ready), HF (Half-full Flag), PAE (Programmable Almost-Empty flag) and PAF (Programmable Almost-Full flag). The EF and FF functions are selected in IDT Standard mode. The IR and OR functions are selected in FWFT mode. HF, PAE and PAF are always available for use, irrespective of timing mode. PAE and PAF can be programmed independently to switch at any point in memory. (See Table 1 and Table 2.) Programmable offsets determine the flag switching threshold and can be loaded by two methods: parallel or serial. Two default offset settings are also provided, so that PAE can be set to switch at 127 or 1,023 locations from the empty boundary and the PAF threshold can be set at 127 or 1,023 locations from the full boundary. These choices are made with the LD pin during Master Reset. For serial programming, SEN together with LD on each rising edge of WCLK, are used to load the offset registers via the Serial Input (SI). For parallel programming, WEN together with LD on each rising edge of WCLK, are used to load the offset registers via Dn. REN together with LD on each rising edge of RCLK can be used to read the offsets in parallel from Qn regardless of whether serial or parallel offset loading has been selected. During Master Reset (MRS) the following events occur: The read and write pointers are set to the first location of the FIFO. The FWFT pin selects IDT Standard mode or FWFT mode. The LD pin selects either a partial flag default setting of 127 with parallel programming or a partial flag default setting of 1,023 with serial programming. The flags are updated according to the timing mode and default offsets selected. The Partial Reset (PRS) also sets the read and write pointers to the first location of the memory. However, the timing mode, partial flag program- ming method, and default or programmed offset settings existing before Partial Reset remain unchanged. The flags are updated according to the timing mode and offsets in effect. PRS is useful for resetting a device in mid-operation, when reprogramming partial flags would be undesirable. The Retransmit function allows data to be reread from the FIFO more than once. A LOW on the RT input during a rising RCLK edge initiates a retransmit operation by setting the read pointer to the first location of the memory array. If, at any time, the FIFO is not actively performing an operation, the chip will automatically power down. Once in the power down state, the standby supply current consumption is minimized. Initiating any operation (by acti- vating control inputs) will immediately take the device out of the power down state. The IDT72V261LA/72V271LA are fabricated using IDT’s high speed submicron CMOS technology. |
Similar Part No. - 72V261LA20TFGI8 |
|
Similar Description - 72V261LA20TFGI8 |
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
