Electronic Components Datasheet Search |
|
CAT5241UI-25 Datasheet(PDF) 2 Page - Catalyst Semiconductor |
|
CAT5241UI-25 Datasheet(HTML) 2 Page - Catalyst Semiconductor |
2 / 16 page 2 CAT5241 Document No. 2011, Rev. J PIN DESCRIPTION Pin (SOIC) Name Function 1RW0 Wiper Terminal for Potentiometer 0 2RL0 Low Reference Terminal for Potentiometer 0 3RH0 High Reference Terminal for Potentiometer 0 4 A0 Device Address, LSB 5 A2 Device Address 6RW1 Wiper Terminal for Potentiometer 1 7RL1 Low Reference Terminal for Potentiometer 1 8RH1 High Reference Terminal for Potentiometer 1 9 SDA Serial Data Input/Output 10 GND Ground 11 RH2 High Reference Terminal for Potentiometer 2 12 RL2 Low Reference Terminal for Potentiometer 2 13 RW2 Wiper Terminal for Potentiometer 2 14 SCL Bus Serial Clock 15 A3 Device Address 16 A1 Device Address 17 RH3 High Reference Terminal for Potentiometer 3 18 RL3 Low Reference Terminal for Potentiometer 3 19 RW3 Wiper Terminal for Potentiometer 3 20 VCC Supply Voltage PIN DESCRIPTIONS SCL: Serial Clock The CAT5241 serial clock input pin is used to clock all data transfers into or out of the device. SDA: Serial Data The CAT5241 bidirectional serial data pin is used to transfer data into and out of the device. The SDA pin is an open drain output and can be wire- or'd with the other open drain or open collector outputs. A0, A1, A2, A3: Device Address Inputs These inputs set the device address when ad- dressing multiple devices. A total of sixteen devices can be addressed on a single bus. A match in the slave address must be made with the address input in order to initiate communication with the CAT5241. RH, RL: Resistor End Points The four sets of RH and RL pins are equivalent to the terminal connections on a mechanical potenti- ometer. RW: Wiper The four RW pins are equivalent to the wiper terminal of a mechanical potentiometer. DEVICE OPERATION The CAT5241 is four resistor arrays integrated with 2- wire serial interface logic, four 6-bit wiper control registers and sixteen 6-bit, non-volatile memory data registers. Each resistor array contains 63 separate resistive elements connected in series. The physical ends of each array are equivalent to the fixed terminals of a mechanical potentiometer (RH and RL). RH and RL are symmetrical and may be interchanged. The tap positions between and at the ends of the series resistors are connected to the output wiper terminals (RW) by a CMOS transistor switch. Only one tap point for each potentiometer is connected to its wiper terminal at a time and is determined by the value of the wiper control register. Data can be read or written to the wiper control registers or the non-volatile memory data registers via the 2-wire bus. Additional instructions allow data to be transferred between the wiper control registers and each respective potentiometer's non-volatile data registers. Also, the device can be instructed to operate in an "increment/decrement" mode. |
Similar Part No. - CAT5241UI-25 |
|
Similar Description - CAT5241UI-25 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |