Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.

Low ESR, 105

℃

MZR

Series

・Downsizing and Lower ESR, 2,000hours at 105℃

・Rated voltage range : 6.3 to 50V, Nominal capacitance range : 100 to 2,200μF

・Solvent resistant type(see PRECAUTIONS AND GUIDELINES)

・Vibration resistance structure

・RoHS Compliant

・AEC-Q200 compliant : Please contact Chemi-Con for more details, test data, information.

◆SPECIFICATIONS

Items

Characteristics

Category

Temperature Range

-55 to +105

℃

Rated Voltage Range

Capacitance Tolerance

±20% (M)

(at 20

℃, 120Hz)

Leakage Current

I=0.01CV or 3μA, whichever is greater.

Where, I : Max. leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V)

(at 20

℃ after 2 minutes)

Dissipation Factor

(tanδ)

6.3V 10V

16V

25V

35V

50V

(at 20

℃, 120Hz)

tan

δ(Max.)

0.26 0.19 0.16 0.14 0.12 0.10

Low Temperature

Characteristics

(Max. Impedance Ratio)

6.3V 10V

16V

25V

35V

50V

(at 120Hz)

Z(-25

℃)/Z(+20℃)

2

2

2

2

2

2

Z(-40

℃)/Z(+20℃)

3

3

3

3

3

3

Z(-55

℃)/Z(+20℃)

4

4

4

3

3

3

Endurance

The following specifications shall be satisfied when the capacitors are restored to 20

℃ after the rated voltage is applied for 2,000 hours

at 105

℃.

Capacitance change

≦±30% of the initial value

D.F. (tan

δ)

≦200% of the initial specified value

Leakage current

≦The initial specified value

Shelf Life

The following specifications shall be satisfied when the capacitors are restored to 20

℃ after exposing them for 1,000 hours at 105℃ without

voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.

Capacitance change

≦±30% of the initial value

D.F. (tan

δ)

≦200% of the initial specified value

Leakage current

≦The initial specified value

Surge Voltage Test

The capacitors shall be subjected to 1,000 cycles each consisting of charging with the specified surge voltage for 30

±5 seconds through

a protective resistor (as required for RC=0.1

±0.05sec) and open-circuiting for 5.5 minutes at a room temperature of 15 to 35℃.

6.3V 10V

16V

25V

35V

50V

7.2V 12V

18V

29V

40V

58V

Appearance

No significant damage

Capacitance change

≦±20% of the initial value

D.F. (tan

δ)

≦200% of the initial specified value

Leakage current

≦The initial specified value

(Caution)

Surge Voltage Test intends to evaluate capacitors in durability of an exceptional excessive voltage under specific conditions.It does

not imply long-term use at all.

◆DIMENSIONS [mm]

L

±0.3 (Note)

0.3max.

A

±0.2

W

Note : L

±0.5 for HA0 and JA0

L

±0.5

0.3max.

A

±0.2

W

: Dummy terminals

●

Size code : F80 to JA0

●

Terminal Code : G(Vibration resistant structure)

●

Size code : HA0 and JA0

●

Terminal Code : A

Vent for JA0

Vent for JA0

◆MARKING

3Q

330

EX) 35V330

µF

●

Rated voltage symbol

Symbol

6.3

10

16

25

35

j

A

C

E

V

50

H

Applying voltage over the rated voltages causes the capacitors to have short lifetime.

Besides, applying voltage over the specified surge voltages may cause to have short circuit failure. A protection

circuit should be used if applied voltage will exceed the rated voltages.

Downsized

MZR

MZJ P98

Size code

F80

HA0

JA0

D

6.3

8

10

L

7.7

10.0

10.0

A

6.6

8.3

10.3

B

6.6

8.3

10.3

C

7.2

9.0

11.0

W

0.5 to 0.8

0.7 to 1.1

0.7 to 1.1

P

1.9

3.1

4.5

96

CAT. No. E1001Q

SURFACE MOUNT ALUMINUM ELECTROLYTIC CAPACITORS