 |
Electronic Components Datasheet Search |
|
|
Electronic Components Datasheet Search |
|
RS2-2415S10A3M Datasheet(PDF) 3 Page - RSG Electronic Components GmbH |
|
||||||||||||||||||||||||||||||
RS2-2415S10A3M Datasheet(HTML) 3 Page - RSG Electronic Components GmbH |
|
|
3 / 4 page  RSG Electronic Components GmbH •Sprendlinger Ldst. 115 • 63069 Offenbach •+49 69-984047-0 •rsg-electronic.de page 3 (4) Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C3 C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C3 C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. DC/DC-Converter 1.0W semi-regulated Single & Dual Output we energize electronics! an acal group company we energize electronics! Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C3 C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. Output Ripple & Noise Measurement Test The Scope measurement bandwidth is 0-20MHz. EMI Filter Input filter components (C1, L,C2,C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Load C3 C1 L C2 C3 RS2-05XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-12XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-15XXS/D10AXM 1210, 2.2uF/100V 18uH RS2-24XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV RS2-48XXS/D10AXM 1210, 2.2uF/100V 18uH 1210, 2.2uF/100V 1206, 470pF/2KV +Vout +Vin DC/DC Converter -Vin -Vout L Load C1 C2 +Vout DC/DC Converter -Vout Scope 1. Ripple/Noise measured with 20MHz bandwidth. 2. Tested by minimal Vin and constant resistive full load. 3. Input filter components (C1, L,C2, C3) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 4. An external filter capacitor is required if the module has to meet IEC61000-4-4 The filter capacitor RSG suggest: Nippon chemi-con KY series, 220uF/100V. 5. Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 6. Operation under no-load conditions will not damage these devices, however they may not meet all listed specifications. |
Similar Part No. - RS2-2415S10A3M |
|
Similar Description - RS2-2415S10A3M |
|
|
|
Link URL |
| Privacy Policy |
| ALLDATASHEET.COM |
| Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
| Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
|
Family Site : ic2ic.com |
icmetro.com |
English ▼
English
Chinese
German
Japanese
Russian
Korean
Spanish
French
Italian
Portuguese
Polish
Vietnamese
Indian
Mexican
British
New Zealand
