Electronic Components Datasheet Search |
|
RM15WTPZA-2S Datasheet(PDF) 8 Page - Hirose Electric |
|
RM15WTPZA-2S Datasheet(HTML) 8 Page - Hirose Electric |
8 / 16 page 8 BPlug -- Disassembly / Assembly 5. 4. 3. 2. 1. Disassembly 1 Fix the plug in the assembly fixture (RM15TP-T01 (CL150-0098-0)), then remove the insulator body (P) and the back shell. Right-angle plugs have set screws in the tightening ring at 2 locations. Loosen the set screws before removing the back shell. 2 Remove the 2 screws of the strain relief clamp, and then remove the clamp from the tightening collar. Part Name Number of Contacts 3 2,4,8,10,12 3 2,4,8,10,12 10,12 A 6mm 3mm 6mm 3mm 3mm B 21mm 21mm 12mm 12mm 25mm Cable jacket Cable Wires Conductors B A 3 min Strain relief clamp Back shell Coupling Tightening collar Washer Bushing Insulator body (P) Contacts Clamp Screw Cable Set screw(2) Back shell Tightening ring Wiring 1 Assure that the cable outer diameter will fit the strain relief clamp, and is prepared as recommended in Table 1. It is recommended that the exposed conductors be pre-soldered, to assure easier insertion in the soldering cup. 2 Pass the parts over the cable in the order of: tightening collar, washer, bushing, back shell, and coupling. Refer to the drawings (above) for assembly orientation of all components. 3 Solder the wires to the contacts of the insulator body (P). Use of heat-shrink tubing or another insulating media between the soldered contacts is suggested. Connector Assembly Straight Plugs 1 Place the completely wired insulator body (P) in the assembly fixture secured in a vise. Insert in the coupling, then back shell. The back shell should be tightened to a torque of 3 N•m. Right-angle Plugs 1 Place the completely wired insulator body (P) in an assembly fixture secured by a vise. Insert in the coupling, then back shell (with tightening ring). When attaching the back shell, orient the cable in the desired direction and fasten the tightening ring to the insulator body (P) with a torque of 3 N•m. After this, tighten and fix the 2 sets crews with a torque of 0.2 to 0.3 N•m. Additional assembly recommendations: In applications where continuous extremely high vibrations may be encountered it is recommended that a thread locking compound be applied to male threads prior to assembly (Loctite 271 ˛ manufactured by Henkel Japan K.K. or equivalent) Waterproof verification - plug assembly Apply air pressure of 17.6 kPa for 30 seconds from the mating side of the plug assembly. There shall not be any air leakage from inside the connector when submerged in the water tank. Precautions 1 Follow the correct assembly sequence, cable preparation and tightening torques. 2 Assure that the applicable cable outer surfaces are free of scratches, oil, grease or any other contamination. 3 Do not use excessive forces or improper tools when assembling or mounting the connectors. RM15WTPZA-ππ RM15WTPZ-ππ RM15WTLP-ππ Table 1 The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information. All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative. |
Similar Part No. - RM15WTPZA-2S |
|
Similar Description - RM15WTPZA-2S |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |