INA331 datasheet(10/22 Pages) TI1

Part #	INA331

Description	INSTRUMENTATION AMPLIFIERS

Download	22 Pages

Scroll/Zoom	100%

Manufacturer	TI1 [Texas Instruments]

Direct Link	http://www.ti.com

Logo

10 / 22 page

INA331, INA2331

SBOS215C

10

www.ti.com

SETTING THE GAIN

The ratio of R2 to R1, or the impedance between pins 1, 5,

and 6, determines the gain of the INA331. With an internally

set gain of 5, the INA331 can be programmed for gains

greater than 5 according to the following equation:

G = 5 + 5 (R2/R1)

The INA331 is designed to provide accurate gain, with gain

error less than 0.1%. Setting gain with matching TC resistors

will minimize gain drift. Errors from external resistors will add

directly to the error, and may become dominant error sources.

COMMON-MODE INPUT RANGE

The upper limit of the common-mode input range is set by the

common-mode input range of the second amplifier, A2, to

1.2V below positive supply. Under most conditions, the

amplifier operates beyond this point with reduced perfor-

mance. The lower limit of the input range is bounded by the

output swing of amplifier A1, and is a function of the refer-

ence voltage according to the following equation:

VOA1 = 5/4 VCM – 1/4 VREF

(See typical characteristics

Common-Mode Input Range vs

Reference Voltage.)

REFERENCE

The reference terminal defines the zero output voltage level.

In setting the reference voltage, the common-mode input of

A3 should be considered according to the following equation:

VOA2 = VREF + 5 (VIN+ – VIN–)

For ensured operation, VOA2 should be less than

VDD – 1.2V.

The reference pin requires a low-impedance connection. As

little as 160

Ω in series with the reference pin will degrade the

CMRR to 80dB. The reference pin may be used to compen-

sate for the offset voltage (see Offset Trimming section). The

reference voltage level also influences the common-mode

input range (see Common-Mode Input Range section).

INPUT BIAS CURRENT RETURN

With a high input impedance of 1013

Ω, the INA331 is ideal for

use with high-impedance sources. The input bias current of

less than 10pA makes the INA331 nearly independent of

input impedance and ideal for low-power applications.

For proper operation, a path must be provided for input bias

currents for both inputs. Without input bias current paths, the

inputs will “float” to a potential that exceeds common-mode

range and the input amplifier will saturate. Figure 3 shows

FIGURE 3. Providing an Input Common-Mode Path.

how the bias current path can be provided in the cases of

microphone applications, thermistor applications, ground re-

turns, and dc-coupled resistive bridge applications.

When differential source impedance is low, the bias current

return path can be connected to one input. With higher

source impedance, two equal resistors will provide a bal-

anced input. The advantages are lower input offset voltage

due to bias current flowing through the source impedance

and better high-frequency gain.

47k

Ω

Microphone,

Hydrophone,

etc.

Center-tap

provides bias

current return

Bridge resistance

provides bias

current return

Transformer

Bridge

Amplifier

Bridge

Sensor

V

B

(1)

V

B

(1)

V

EX

NOTE: (1) V

B is bias voltage within

common-mode range, dependent

on REF.

INA331

5

3

2

8

7

6

4

1

V+

Shutdown

V

IN–

V–

V

IN+

REF

INA331

5

3

2

8

7

6

4

1

V+

Shutdown

V

IN–

V–

V

IN+

REF

INA331

5

3

2

8

7

6

4

1

V+

Shutdown

V

IN–

V–

V

IN+

REF

V

OUT

RG

V

OUT

RG

V

OUT

RG

Similar Part No. - INA331

Manufacturer	Part #	Datasheet	Description
Texas Instruments	INA331	294Kb / 15P	[Old version datasheet] Low-Power, Single-Supply, CMOS INSTRUMENTATION AMPLIFIERS
	INA331AIDGKR	294Kb / 15P	[Old version datasheet] Low-Power, Single-Supply, CMOS INSTRUMENTATION AMPLIFIERS
	INA331AIDGKT	294Kb / 15P	[Old version datasheet] Low-Power, Single-Supply, CMOS INSTRUMENTATION AMPLIFIERS
	INA331IDGKR	294Kb / 15P	[Old version datasheet] Low-Power, Single-Supply, CMOS INSTRUMENTATION AMPLIFIERS
	INA331IDGKT	294Kb / 15P	[Old version datasheet] Low-Power, Single-Supply, CMOS INSTRUMENTATION AMPLIFIERS

More results

Similar Description - INA331

Manufacturer	Part #	Datasheet	Description
Texas Instruments	INA332	994Kb / 22P	[Old version datasheet] INSTRUMENTATION AMPLIFIERS
Intersil Corporation	EL4430	185Kb / 10P	Video Instrumentation Amplifiers
Elantec Semiconductor	EL4430C	311Kb / 12P	Video Instrumentation Amplifiers
Texas Instruments	INA128	1Mb / 20P	[Old version datasheet] Precision, Low Power INSTRUMENTATION AMPLIFIERS
	INA128-HT	834Kb / 30P	[Old version datasheet] Precision, Low-Power Instrumentation Amplifiers
	INA129-EP	1Mb / 26P	[Old version datasheet] Precision, Low Power Instrumentation Amplifiers
	INA128-HT	1Mb / 29P	[Old version datasheet] PRECISION, LOW POWER INSTRUMENTATION AMPLIFIERS
	INA129-EP	1Mb / 22P	[Old version datasheet] PRECISION, LOW POWER INSTRUMENTATION AMPLIFIERS
Burr-Brown (TI)	INA128	245Kb / 10P	Precision, Low Power INSTRUMENTATION AMPLIFIERS
Texas Instruments	INA129UA	1Mb / 20P	[Old version datasheet] Precision, Low Power INSTRUMENTATION AMPLIFIERS

More results

INA331 Datasheet(PDF) 10 Page - Texas Instruments

INA331 Datasheet(HTML) 10 Page - Texas Instruments

Similar Part No. - INA331

Similar Description - INA331

Html Pages

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Datasheet Download

Link URL