Electronic Components Datasheet Search |
|
DSC2033FE2 Datasheet(PDF) 2 Page - Micrel Semiconductor |
|
DSC2033FE2 Datasheet(HTML) 2 Page - Micrel Semiconductor |
2 / 5 page ______________________________________________________________________________________________________________________________________________ DSC2033 Page 2 MK-Q-B-P-D-12042609-2 DSC2033 Low-Jitter Configurable Dual LVDS Oscillator Pin Description Pin No. Pin Name Pin Type Description 1 Enable I Enables outputs when high and disables when low 2 NC NA Leave unconnected or grounded 3 NC NA Leave unconnected or grounded 4 GND Power Ground 5 FS0 I Least significant bit for frequency selection 6 FS1 I Middle bit for frequency selection 7 FS2 I Most significant bit for frequency selection 8 Output1+ O Positive LVDS Output 1 9 Output1- O Negative LVDS Output 1 10 Output 2- O Negative LVDS Output 2 11 Output 2+ O Positive LVDS Output 2 12 VDD2 Power Power Supply 2 for LVDS Output 2 13 VDD Power Power Supply 14 NC NA Leave unconnected or grounded Operational Description The DSC2033 is a dual output LVDS oscillator consisting of a MEMS resonator and a support PLL IC. The two outputs are generated through independent 8-bit programmable dividers from the output of the internal PLL. Two constraints are imposed on the output frequencies: 1) f2=M x f1/N, where M and N are even integers between 4 and 254, 2) 1.2GHz < N x f2 < 1.7GHz. The actual frequencies output by the DSC2033 are controlled by an internal pre-programmed memory (OTP). This memory stores all coefficients required by the PLL for up to eight different frequency combinations. Three control pins (FS0 – FS2) select the output frequency combination. Discera supports customer defined versions of the DSC2033. Standard frequency options are described in in the following sections. When Enable (pin 1) is floated or connected to VDD, the DSC2033 is in operational mode. Driving Enable to ground will tri-state both output drivers (hi-impedance mode). Output Clock Frequencies Table 1 lists the standard frequency configurations and the associated ordering information to be used in conjunction with the ordering code above. Customer defined combinations are available. Table 1. Pre-programmed pin-selectable output frequency combinations Ordering Info Freq (MHz) Freq Select Bits [FS2, FS1, FS0] – Default is [111] 000 001 010 011 100 101 110 111 G0001 fOUT1 148.5 156.25 150 125 125 100 100 400 fOUT2 74.25 125 125 25 50 50 75 200 G0002 fOUT1 100 125 0 0 0 0 0 0 fOUT1 100 125 0 0 0 0 0 0 GXXXX fOUT1 Contact factory for additional configurations. fOUT2 Frequency select bit are weakly tied high so if left unconnected the default setting will be [1] and the device will output the associated frequency highlighted in Bold. |
Similar Part No. - DSC2033FE2 |
|
Similar Description - DSC2033FE2 |
|
|
Link URL |
Privacy Policy |
ALLDATASHEET.COM |
Does ALLDATASHEET help your business so far? [ DONATE ] |
About Alldatasheet | Advertisement | Datasheet Upload | Contact us | Privacy Policy | Link Exchange | Manufacturer List All Rights Reserved©Alldatasheet.com |
Russian : Alldatasheetru.com | Korean : Alldatasheet.co.kr | Spanish : Alldatasheet.es | French : Alldatasheet.fr | Italian : Alldatasheetit.com Portuguese : Alldatasheetpt.com | Polish : Alldatasheet.pl | Vietnamese : Alldatasheet.vn Indian : Alldatasheet.in | Mexican : Alldatasheet.com.mx | British : Alldatasheet.co.uk | New Zealand : Alldatasheet.co.nz |
Family Site : ic2ic.com |
icmetro.com |